Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 115 / 212

111

Maintenance

Engine Cooling System

Cooling System Bleeding

Bleeding the cooling system is required only if the system has been drained for maintenance

and/or repair. Always allow the engine to cool sufficiently before removing the radiator pres-

sure cap.
1. Remove the pressure cap.
2. Using a funnel, slowly add the recommended coolant. Fill the radiator to the bottom of

the filler neck.

3. Reinstall the pressure cap.
4. Start the engine and allow it to idle for five minutes, or until operating temperature is

reached.

5. Stop the engine.
6. After the engine has cooled, add additional coolant to refill the radiator to the bottom of

the filler neck.

7. Operate the vehicle for 20 minutes, allow the engine to cool, then recheck the coolant

level in the radiator. Add coolant as needed.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды