Polaris 2010 OUTLAW 450 MXR страница 111 Скачать руководство пользователя

Страница: 111 / 212

107

Maintenance

Engine Oil Change

Changing Oil Filters

6. Grease the filter cover O-rings (3).
7. Reinstall the covers and the screws. Tighten

screws to 4.5 ft. lbs. (6 Nm).

8. Remove the oil fill plug (4). Add 40 oz. (1.2

liters) of the recommended engine oil (see page

98). Reinstall the fill plug.

9. Start the engine. Allow it to idle for at least one

minute to fully distribute the new oil. Stop the

engine.

10. Check for leaks at all threaded connections and

at the oil filter covers.

11. View the oil level in the sight glass. Add oil as

needed to maintain the level as recommended

(see page 99).

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды