Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 60 / 212

Features and Controls

Choke

The choke assists in starting a cold engine. The choke

knob is located on the left side of the carburetor. Refer

to the engine starting procedure on page 66 for correct

choke and throttle settings during starting.

Fuel Tank

The fuel tank filler cap is located directly below the

handlebar. Polaris recommends the use of 91 octane or

higher fuel.

Do not use fuel with ethanol content

greater than 10 percent, such as E-85 fuel.

Fuel Filter

The fuel tank has an internal fuel filter. Do not attempt to clean the fuel filter. See your

Polaris dealer for service if you suspect the fuel filter is plugged.

Choke Knob

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды