Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 146 / 212

142

Maintenance

Brakes

Under normal operation, the diaphragm extends into the reservoir as fluid level drops. If the

fluid level is low and the diaphragm is not extended, a leak is likely and the diaphragm

should be replaced. To ensure proper diaphragm operation, always fill the reservoir as

needed whenever the cover is loosened or removed. Do not overfill.

WARNING!

An over-full master cylinder may cause brake drag or brake lock-up, which could result in

serious injury or death. Maintain brake fluid at the recommended level. Do not overfill.

Both brakes are self-adjusting, but the following checks are recommended to keep the brake

systems in good operating condition. Check more often if brakes are used heavily under nor-

mal operation.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды