Polaris 2010 OUTLAW 450 MXR страница 119 Скачать руководство пользователя

Страница: 119 / 212

115

Maintenance

Carburetor Jetting

Carburetor re-jetting can be performed to compensate for altitude and/or temperature

changes. If the vehicle is to be operated at various altitudes and temperatures, certain adjust-

ments can be made to improve its operation and driveability. Above 6000 feet (1800 m) the

engine air/fuel mixture becomes overly rich. An engine loses approximately 3% of its power

for each 1000-foot (305 m) increase in elevation. Although this power cannot be regained,

changes to the carburetor and drive system can be made to allow more efficient operation.
Contact your dealer for altitude adjustments. Your dealer has the training and special tools

required to perform these modifications.

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды