Polaris 2010 OUTLAW 450 MXR Скачать руководство пользователя

Страница: 202 / 212

198

Warranty

U.S.A. EPA Emissions Limited Warranty

For exhaust emissions, emission-related components include any engine parts related to the following systems:

The following parts are also considered emission-related components for exhaust emissions:

The following parts are considered emission-related components for evaporative emissions:

*As related to the evaporative emission control system.

• Air-induction system

• Ignition system

• Fuel system

• Exhaust gas recirculation systems

• Aftertreatment devices

• Sensors

• Crankcase ventilation valves

• Electronic control units

• Fuel Tank

• Vacuum Control Diaphragms*

• Fuel Cap

• Control Cables*

• Fuel Line

• Control Linkages*

• Fuel Line Fittings

• Purge Valves

• Clamps*

• Vapor Hoses

• Pressure Relief Valves*

• Liquid/Vapor Separator

• Control Valves*

• Carbon Canister

• Control Solenoids*

• Canister Mounting Brackets

• Electronic Controls*

• Carburetor Purge Port Connector

Содержание 2010 OUTLAW 450 MXR





















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 450 MXR, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 450 MXR

Отзывы:

Похожие инструкции для 2010 OUTLAW 450 MXR

Бренды по названию

Популярные бренды