PUM_SBT_091102_EN
4/38
Installation
• The installation of the products should only be performed
by trained and authorised persons. For other persons and
to be trained persons the products should only be handled
under supervision of a responsible and authorised person
when installing.
• Please use appropriate lifing materials and equipment when
working in an area over 2m / 6.5 feet.
• Please ensure that, on the side of the vehicle were the
system is installed, no persons are present in an area
of 1 (one) meter under and / or around the SBT system
and /or between the vehicle and the entry / exit door when
the vehicle exits the building. This way possible injuries can
be avoided by a possible backwards motion of the
Grabber® in the direction of the station and park position.
• Never install the product in front of entries, exits or
passage ways which are to be used by emergecy services.
• Check before installation if the structure of the wall / roof
is stabile enough to hold the components which are to be
attached to it.
• Use common sense. Stay alert and keep your attention to
your work. Do not use the product when you are under
the influence of drugs, alcohol or medicine.
• Air, which might contain health hazardous components,
such as chrome, Nickel, Beryllium, Cadmium, Lead etc.
should never be recycled. This type of air must always be
removed from the working area.
Use
• Inspect the product and check for damages. Verify the
functioning of the safety features.
• Check the working area. Please keep unauthorised persons
away from the working area.
• Protect the product against water and humidity.
• Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
• Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers if any
elctronics, such as control boxes, are used.
• The user of the product always has full responsibility for
the correct execution of the safety guidelines and
instructions. These are all the safety guidelines and
instructions which apply to the use of the system.
Service, maintenance and repairs
• Observe the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
• Always use tools, materials, lubricants and service techni-
ques which have been approved by the manufacturer.
Never use worn tools and do not leave any tools in or on
the product.
• Safety features which have been removed for service,
maintenance or repairs, must be put back immediately after
finishing these jobs and it must be checked that they still
function properly.
• Please ensure that no vehicle enters or exits the station
during the service, maintenance and repair activities.
Tools
These tools are needed to install the Plymovent System:
- Power drill
- Battery operated power drill
- Alllen key set
- Phillips srewdriver set
- Measuring tape
Please note that additional tools and machines may be needed
depending on the installation situation (installation height,
space available etc).
CE declaration of conformity for machinery
”We, Plymovent, Kopparbergsgatan 2, SE-214 44 Malmö,
Sweden, herewith declare, on our own responsibility, that the
product(s):
- Sliding Balancer Track System
is/are in conformity with the following harmonized standard(s)
and/or other such normative doc amendments, if any:
DIN 14572:2002
DIN 31000/A1:2007
DIN EN 12100-1/A1:2009
DIN EN 12100-2/A1:2009
ZEK 01.02-08
Alkmaar, the Netherlands, 18-06-2010
C.J.M. Knijn
Chief Operations Officer
ATTENTION!
Service, Maintenance and Repairactivities shall only
be performed (in line with TRGS 554) by authorized,
trained and qualified personnel taking into account
the applicable working practices and safety regula-
tions.
ATTENTION!
After shutting down the ventillation system wait
minimal 10 seconds before handeling the system and
prodcuts when performing service, maintenance and
/ or repairs.
5.
CE DECLARATION
