Piper Cherokee LANCE страница 820 Скачать руководство пользователя | Manualshive

Страница: 820 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

III - INSPECTION

07/15/06

4F14

b

If the insulation material has not been wet, or if new material is being installed,
ensure a six (6) inch clearance in the insulation has been cut out in all directions
around each attach fitting.

5

Locate the two 0.191 inch drain holes, one beneath each rear attach fitting, in the
bottom fuselage skin and ensure each is clean and free of obstruction.

NOTE: If there are no drain holes, install them as described in Figure 3-16.

6

Re-install floorboards, seats, interior panels, and other articles previously removed.
Perform a functional test of any system or component that may have been interrupted
or removed.

(21) FUEL TANK / WING SPAR CORROSION INSPECTION. (See Figures 3-17 and 3-18.)

NOTE: Paragraphs (a) and (b), below, are keyed to Figures 3-17 and 3-18.

(a) Each seven (7) calendar years time-in-service, remove the fuel tanks and conduct

inspections as specified below. Each inspection is for corrosion (intergranular, exfoliation,
etc.), but while exposed all areas and parts should be checked for other anomalies such as
damage, cracking, or wear. Any part or area determined to be defective must be repaired
or replaced using standard FAA approved parts and methods.

A1. Inspect the entire spar and all spar angles behind each fuel tank with special attention

to the area of the inboard upper and lower spar caps. If corrosion is detected,
accomplish a thorough inspection throughout the wing.

A2. Inspect the spar and forward attach fitting for condition and security. Check for

loose, damaged or broken bolts or nuts.

A3. Inspect fuel tank attach hardware and gang channels (nut plate strips) for condition.

Replace as required.

A4. Replace flexible fuel vent hoses. Inspect vent hard lines for exterior and interior

corrosion. Flush hard lines with mineral spirits under pressure through a clean cloth.
If excessive debris or corrosion deposits are observed replace the line.

A5. Remove fuel quantity senders. Inspect for condition, operation, and security and

freedom of the float on the arm. Inspect the condition of wires and terminals.
Replace components as required. Replace the gaskets.

A6. Inspect flexible fuel hoses and couplings. Replace as required.

WARNING: SLOSHING COMPOUND PROHIBITED.

A7. Inspect the exterior of each fuel tank for leaks. Inspect the interior for corrosion or

evidence of sloshing compound. If either condition exists, clean, repair or replace the
fuel tank.

(b) Treat the following areas with Dinotrol AV 8 (P/N 89500-800; two (2) each per airplane)

before reassembly.

B1. Entire wing spar, spar angles (cap), and ribs behind and adjacent to each fuel tank.

«
...
818
819
820
821
822
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: SKY PARAGLIDERS Страницы: 51

Бренд: Sky Country Страницы: 19

Бренд: PLKB Страницы: 12

Бренд: S-TEC Страницы: 78

Бренд: Tecnam Страницы: 162

Бренд: Swing Страницы: 22

Бренд: Swing Страницы: 36

Powerplay Sting 2

Бренд: Swing Страницы: 55

Бренд: Parachutes de France Страницы: 72

Бренд: Zenair Страницы: 78

Бренд: Nervures Страницы: 20

Бренд: PCM Страницы: 14

Бренд: PCM Страницы: 17

Bristell B23-915

Бренд: BRM Aero Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды