Piper Cherokee LANCE страница 255 Скачать руководство пользователя | Manualshive

Страница: 255 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

VI - LANDING GEAR AND BRAKE SYSTEM

(PA-32-260/300)

2A11

e.

To remove the strut assembly from the strut housing (4), cut the safety wire at the top of the housing
that secures the steering horn attaching bolt to the tube retainer nut . Then remove the steering horn
attaching bolt and the flat head pin, thus relieving the steering horn from the top of the strut
housing.

f.

Loosen the strut assembly retainer nut (l) that secures the strut assembly in the strut housing. At the
same time, slide the strut assembly out through the bottom of the strut housing. Remove the nut (l)
and washer (2) from the top of the strut housing after the assembly is removed.

NOTE: The strut assembly may fit tight inside of the housing. It may be necessary to tap the top of

the fork with a plastic mallet.

g.

If desired, remove the top and bottom bearing (3 and 5) from the strut housing. The bearings are
compressed slightly into place, and light tapping may be needed to free them.

h.

To remove the piston tube and fork assembly (17) from the cylinder (9), proceed as follows:

1.

Separate the upper and lower torque links by removing the connecting nut, washer and bolt.

2.

Compress the piston tube and fork assembly slightly and remove the retainer ring (10) from the
annular slot in the bottom of the cylinder tube . Then remove piston tube and fork assembly by
sliding out from the bottom of the cylinder tube.

i.

To remove the bearing assembly from the piston tube, release the snap ring (11) from the top of the
piston tube and slide bearing assembly off the end.

1.

If desired, carefully remove the wiper strip (16), back-up washer (15) and quad ring or “O”
ring (14) from the inside of the bearing sleeve, and also the “O” ring gasket (13) from the
outside of the bearing sleeve.

j.

To remove the piston tube plug (19) with “0” ring (18) located in the lower end of the tube, the
following procedure may be used:

1.

Remove the nose wheel from the fork as described in paragraph 6-21.

2.

Loosen and remove the bolt, washer and nut that extends through the piston tube and block
assembly.

3.

Push the plug through the top of the piston tube by use of a rod inserted through the bottom of
the tube.

6-7. CLEANING, INSPECTION AND REPAIR OF NOSE GEAR OLEO.

a.

Clean all parts with a suitable dry type cleaning solvent.

b.

Inspect the landing gear oleo assembly component for the following:

1.

Cylinder tube assembly for corrosion, scratches, nicks and excessive wear.

2.

Lock rings for cracks, burrs, wear.

3.

Fork assembly for corrosion, scratches, nicks, and misalignment.

4.

Link assembly for elongated holes, cracks, corrosion, scratches, nicks and straightness.

5.

General condition of air valve.

c.

Repair of the oleo is limited to smoothing out minor scratches, nicks and dents and replacement of
parts.

«
...
253
254
255
256
257
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: The Airplane Factory, Inc Страницы: 166

Бренд: SOARING MODELS Страницы: 12

Бренд: SOL paragliders Страницы: 26

Бренд: Gulfstream Страницы: 30

Бренд: SOL paragliders Страницы: 29

Бренд: XtremeAIR Страницы: 284

Бренд: SKY PARAGLIDERS Страницы: 33

Бренд: Ozone Страницы: 20

Бренд: DUC Hélices Страницы: 27

Бренд: Schildkröt Страницы: 32

Бренд: Stevens Aero Model Страницы: 52

Бренд: Learjet Страницы: 210

Бренд: Learjet Страницы: 373

Бренд: Foxcon Страницы: 13

Бренд: Rolladen-Schneider Страницы: 57

Бренд: Jabiru Страницы: 67

Бренд: Kavan Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды