manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

VIA - LANDING GEAR AND BRAKE SYSTEM

03/27/08

(PA-32R-300)

2C10

k.

To remove the orifice tube (30), remove the large locknut (16) and lock washer (19) from the top of
the cylinder. Pull the tube from the cylinder. 

1.

The orifice plate (31) is removed from the bottom of the orifice tube by releasing the snap ring (32)
that holds the plate in position. 

m.

To remove the piston tube plug (40) with “O” ring (41) located in the lower end of the tube, remove
the bolt assembly and insert a rod up through the hole in the body of the fork (42). Push the plug
out through the top of the tube. 

6A-7.

CLEANING, INSPECTION AND REPAIR OF NOSE GEAR OLEO. 

a.

Clean all parts with a suitable dry type cleaning solvent. 

b.

Inspect the landing gear oleo assembly component for the following:

1.

Bearings and bushings for excess wear, corrosion, scratches and overall damage. 

2.

Retaining pins for wear and damage. 

3.

Lock rings for cracks, burrs, etc. 

4.

Cylinder and orifice tube for corrosion, scratches, nicks and excess wear. 

5.

Upper and lower cylinder bushings loose or turning in cylinder. 

6.

Orifice plate for hole restriction. 

7.

Fork tube for corrosion, scratches, nicks, dents and misalignment. 

8.

Air valve general condition. 

c.

Repair of the oleo is limited to smoothing out minor scratches, nicks and dents and replacement of
parts.

6A-8.

ASSEMBLY OF NOSE GEAR OLEO. (Refer to Figure 6A-l.)

a.

Ascertain that parts are cleaned and inspected.

b.

To install the piston tube plug (40), first lubricate the tube plug and “O” ring (41) with hydraulic
fluid (MIL-PRF-5606) and install the “O” ring on the plug. Lubricate the inside wall of the tube
(39); insert the plug into the top of the tube and push it to the fork end. Align the bolt holes of the
fork, tube and plug, and install bolt assembly.

c.

If desired, cement a cork in the hole in the bottom of the fork body to prevent dirt from entering
between the fork and tube.

d.

To assemble the components of the orifice tube (30), insert the orifice plate (31) into the bottom of
the tube, with the countersunk side of the orifice hole exposed. Secure the plate with the snap ring
(32), lubricate and install the “O” ring (28) on the upper end of the tube.

e.

Insert the orifice tube (30) up through the bottom of the cylinder (23). With the tube exposed
through the top of the cylinder, install the lock washer ( 19) and insert roll pin (18) through the lock
washer into the piston. Install the tube locknut (16) finger tight at this time.

f.

The fork (42) and tube (39) assembly may be assembled by installing the tube components on the
tube. In order, slide onto the tube, the snap ring (38), washer (37), lower bearing (34) with outer and
inner “O” rings (33 and 35) and upper bearing (29). Align the lock pin holes in the upper bearing
with the pin holes in the piston tube (39) and install pins (27).

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Skywalk PEPPER CROSS LIGHT Manual preview
PEPPER CROSS LIGHT
Бренд: Skywalk Страницы: 12
Advance acoustic Pl 3 Manual preview
Pl 3
Бренд: Advance acoustic Страницы: 19
Quickie Q2 Lite Owner'S Manual preview
Q2 Lite
Бренд: Quickie Страницы: 84
Aviation Artur Trendak TERCEL Pilot Operating Handbook preview
TERCEL
Бренд: Aviation Artur Trendak Страницы: 70
Nova IBEX Manual preview
IBEX
Бренд: Nova Страницы: 53
Beechcraft Baron B55 Quick Start Manual preview
Baron B55
Бренд: Beechcraft Страницы: 9
SKY PARAGLIDERS ANTEA L User Manual preview
ANTEA L
Бренд: SKY PARAGLIDERS Страницы: 18
MAC PARA Eden 4 User Manual preview
Eden 4
Бренд: MAC PARA Страницы: 18
MAC PARA Yukon User Manual preview
Yukon
Бренд: MAC PARA Страницы: 28
Ozone Angel v1 Pilot'S Manual preview
Angel v1
Бренд: Ozone Страницы: 23
Ozone Atom 3 Pilot'S Manual preview
Atom 3
Бренд: Ozone Страницы: 18
Dudek VOX-25S User Manual preview
VOX-25S
Бренд: Dudek Страницы: 36
Samba Prestige 2PK Manual preview
Prestige 2PK
Бренд: Samba Страницы: 4
Textron Cessna Citation Sovereign Operation Manual preview
Cessna Citation Sovereign
Бренд: Textron Страницы: 38
SEMROC BlueJay KC-03 Instructions Manual preview
BlueJay KC-03
Бренд: SEMROC Страницы: 6
Nirvana Paramotors KOMAKA User Manual preview
KOMAKA
Бренд: Nirvana Paramotors Страницы: 15
LZ design FES-LAK-P10-100 Manual preview
FES-LAK-P10-100
Бренд: LZ design Страницы: 9
LZ design FES FES-DIS-P1-102 Manual preview
FES FES-DIS-P1-102
Бренд: LZ design Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды