manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

VA - HYDRAULIC SYSTEM

1K3

5A-20. INSTALLATION OF NOSE GEAR ACTUATING CYLINDER. 

a.

Attach the cylinder to its attachment fitting using bolt and nut. 

b.

Attach the operating rod end to the downlock, this will require manually unlocking the nose gear to
allow clearance from the engine mount to install attaching bolt. (Refer to Caution Note Paragraph
5A-16). 

c.

Connect the hydraulic lines to the cylinder fittings. 

d.

Check the adjustment of the cylinder rod end. (Refer to Adjustment of Nose Landing Gear, Section
VIA.) 

e.

Operate pump to purge system of air and check fluid level in reservoir. 

f.

Remove the airplane from jacks.

5A-21. MAIN GEAR ACTUATING CYLINDER.

5A-22. REMOVAL OF MAIN GEAR ACTUATING CYLINDER. 

a.

Place the airplane on jacks. (Refer to Jacking, Section II.) 

b.

Disconnect the hydraulic lines from the actuating cylinder and cover the open line ends to prevent
contamination. 

c.

Disconnect the gear downlock spring from the swivel fitting at the upper end of the spring. 

d.

Remove the downlock spring swivel fitting and disconnect the cylinder operating rod end from the
upper side brace retraction fitting by removing the attaching nut, washer and bolt. 

e.

Disconnect the cylinder from its attachment by removing nut and bolt. 

f.

Remove the cylinder from the wheel well.

5A-23. DISASSEMBLY OF MAIN GEAR ACTUATING CYLINDER. (Refer to Figure 5A-10.) 

NOTE: The following instructions apply to actuators 

P/N 96860-000 (i.e. - SFA232-3 and SFA232-4)

only

. Disassembly, Assembly, and Cleaning, Inspection and Repair instructions for later model

actuators 

P/N 96860-002 and 96860-003 (i.e. - SFA232-5)

are found in Cleveland Wheel and

Brakes publication: Component Maintenance Manual - CMSFA232-5 (011-00504) available
from the vendor. See Vendor Publications in the Introduction.

a.

With the cylinder removed from the airplane, push the piston rod (6) (by hand) toward the clevis (9)
to remove oil from the unit. 

b.

Put clevis (9) only in a soft jaw vise and clamp against the clevis bearing (10). 

c.

If no pipe fitting is installed in the port of the end gland (1), install a fitting (1/8 - 27) into the port.
This fitting need not be tight as it will be used for leverage only. 

d.

Rotate the gland counterclockwise (with use of fitting) until the end of the gland lock ring (4)
shows in the slot in the cylinder body (7). Reverse rotation of the gland (clockwise direction) to
allow the lock ring to move out of the slot. (Refer to Figure 5A-9.) (It may be necessary to give the
ring an assist to start out of the slot. If so, insert a strong wire pick or other available tool in the slot
to lift up the end of the ring and then rotate gland.) 

e.

Pull the piston (6) and end gland from the cylinder. 

f.

Remove O-rings as desired.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Flexifoil CONTROL Instruction Manual preview
CONTROL
Бренд: Flexifoil Страницы: 20
Jabiru j120 Technical Manual preview
j120
Бренд: Jabiru Страницы: 233
SKY PARAGLIDERS METIS 4 User Manual preview
METIS 4
Бренд: SKY PARAGLIDERS Страницы: 33
LET L-23 Super Blanik Flight Manual preview
L-23 Super Blanik
Бренд: LET Страницы: 70
Textron Aviation Cessna 172S NAV III Skyhawk SP Information Manual preview
Cessna 172S NAV III Skyhawk SP
Бренд: Textron Aviation Страницы: 490
FLYSURFER FlyRace Manual preview
FlyRace
Бренд: FLYSURFER Страницы: 6
FLYSURFER CONNECT2 User Manual preview
CONNECT2
Бренд: FLYSURFER Страницы: 20
FLYSURFER EXTACY User Manual preview
EXTACY
Бренд: FLYSURFER Страницы: 44
FLYSURFER Speed 2 User Manual preview
Speed 2
Бренд: FLYSURFER Страницы: 61
FLYSURFER SONIC FR Series Gear Manual preview
SONIC FR Series
Бренд: FLYSURFER Страницы: 92
FLYSURFER NEXT LEAP SPEED4 10.0 Gear Manual preview
NEXT LEAP SPEED4 10.0
Бренд: FLYSURFER Страницы: 132

Бренды по названию

Популярные бренды

Загрузить еще бренды