Piper Cherokee LANCE Скачать руководство пользователя страница 228 | Manualshive

Страница: 228 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

VA - HYDRAULIC SYSTEM

07/15/06

1J24

CAUTION: WHENEVER AIRCRAFT IS PLACED ON JACKS FOR THE PURPOSE OF

MANUALLY RETRACTING THE NOSE GEAR ASSEMBLY, ENSURE THE NOSE
GEAR DOWNLOCK IS FULLY DISENGAGED BEFORE RELEASING THE NOSE
GEAR DRAG LINKS. DAMAGE COULD OCCUR TO THE DOWNLOCK IF NOT
DISENGAGED FULLY.

d.

Disconnect the aft end of cylinder from its attachment fitting and remove the cylinder from the
wheel well.

5A-17. DISASSEMBLY OF NOSE GEAR ACTUATING CYLINDER. (Refer to Figure 5A-8.)

a.

With the cylinder removed from the airplane, remove the fitting from the piston rod (6) end of the
cylinder (7). Mark the position of the fitting to facilitate reinstallation.

b.

On Syncro Devices nose gear actuating cylinders remove the snap ring (l) from the annular slot in
the end of the housing. On Gar-Kenyon nose gear actuating cylinder remove safety wire (9) and
unscrew the end gland (2).

c.

On Syncro Devices assemblies pull the piston (6) with end gland (2) from the cylinder housing. On
Gar-Kenyon assemblies remove piston (6) after unscrewing end gland (2).

5A-18. CLEANING, INSPECTION AND REPAIR OF NOSE GEAR ACTUATING CYLINDER.

a.

Clean the cylinder parts with a suitable dry type solvent and dry thoroughly.

b.

Inspect the cylinder assembly for the following:

1.

Interior walls of the cylinder and exterior surfaces of the piston for scratches, burrs, corrosion,
etc.

2.

Threaded areas for damage.

3.

Rod end fitting and swivel fitting of cylinder for wear and corrosion.

c.

Repairs to the cylinder are limited to polishing out small scratches, burrs, etc. and replacing parts.

5A-19. ASSEMBLY OF NOSE GEAR ACTUATING CYLINDER. (Refer to Figure 5A-8.)

a.

Install “O” ring (5) on the exterior of the end gland (2).

b.

Install “O” ring (4) in the interior of the end gland. The Syncro Devices assemblies also includes a
ring back-up (3) with the “0” ring (4).

c.

Install “O” ring (8) on the body of the piston assembly.

d.

Lubricate the areas around the “O” rings with hydraulic fluid, slide the end gland on the piston rod
and the piston into the cylinder housing (7).

e.

Secure the end gland in the cylinder by installing the snap ring (l) in the annular slot in the Syncro
Devices cylinder. The end gland on the Gar-Kenyon cylinder is secured by threading gland into
cylinder body (7) and securing with safety wire (9).

f.

Install restrictor fitting in the piston rod end of the cylinder.

g.

Check smoothness of operation of the piston.

«
...
226
227
228
229
230
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: P&M Aviation Страницы: 54

Бренд: Skywalk Страницы: 18

Бренд: Sky Страницы: 65

Бренд: Ramsey Electronics Страницы: 24

Бренд: Rans Страницы: 202

Бренд: WINDTECH Страницы: 24

Бренд: Tecnam Страницы: 124

Бренд: DaVinci Страницы: 37

Бренд: Woody Valley Страницы: 28

Бренд: PPGPlans Страницы: 28

Бренд: Foxcon Страницы: 13

Бренд: Crazy Foil Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды