manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию, Страница: 773 / 854

Поделиться
Скачать
Piper Cherokee LANCE Скачать руководство пользователя страница 773

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

03/27/08

III - INSPECTION

4D15

TABLE III-II.  INSPECTION REPORT - PA-32R-300 (cont.)

J.

NOTES

1.

Refer to Piper's Customer Service Information Aerofiche P/N 1753-755 for latest revision
dates to Piper Inspection Reports/Manuals and this service manual. References to
Chapter/Section are to the appropriate Chapter/Section in this manual.

WARNING: INSTRUCTIONS FOR CONTINUED AIRWORTHINESS (ICA) FOR ALL

NON-PIPER APPROVED STC INSTALLATIONS ARE NOT INCLUDED IN
THIS MANUAL. WHEN A NON-PIPER APPROVED STC INSTALLATION IS
INCORPORATED ON THE AIRPLANE, THOSE PORTIONS OF THE
AIRPLANE AFFECTED BY THE INSTALLATION MUST BE INSPECTED
IN ACCORDANCE WITH THE ICA PUBLISHED BY THE OWNER OF THE
STC. SINCE NON-PIPER APPROVED STC INSTALLATIONS MAY
CHANGE SYSTEMS INTERFACE, OPERATING CHARACTERISTICS AND
COMPONENT LOADS OR STRESSES ON ADJACENT STRUCTURES, THE
PIPER PROVIDED ICA MAY NOT BE VALID FOR AIRPLANES SO
MODIFIED.

2.

Inspections or operations are to be performed as indicated by a “O” at the 50 or 100 hour
inspection interval. Inspections or operations (i.e. - component overhauls/replacements, etc.)
required outside the 100 hour cycle are listed as special inspections in Section III. Inspections
must be accomplished by persons authorized by the FAA.

(a) The 50 hour inspection accomplishes preventive maintenance, lubrication and servicing as

well as inspecting critical components.

(b) The 100 hour inspection is a complete inspection of the airplane, identical to an annual inspection.

NOTE: A log book entry should be made upon completion of any inspections.

3.

Piper Service Bulletins are of special importance and Piper considers compliance mandatory.
In all cases, see Service Bulletin/Service Letter Index P/N 762-332 or Service Bulletin/Service
Letter Aerofiche Set P/N 1762-331 to verify latest revision. See also Table III-III.

4.

Piper Service Letters are product improvements and service hints pertaining to servicing the
airplane and should be given careful attention.

5.

Inspections given for the power plant are based on the engine manufacturer’s operator’s
manual (Lycoming P/N 60297-10) for this airplane. Any changes issued to the engine
manufacturer’s operator’s manual shall supersede or supplement the inspections outlined in
this report. Should fuel other than the specified octane rating for the power plant be used, refer
to the latest revision of Lycoming Service Letter No. L185 for additional information and
recommended service procedures. 

6.

Refer to latest revision of Lycoming Service Bulletin No. 480.

7.

Check cylinders for evidence of excessive heat indicated by burned paint on the cylinders. This
condition is indicative of internal damage to the cylinder and, if found, its cause must be
determined and corrected before the airplane is returned to service. Heavy discoloration and
appearance of seepage at the cylinder head and barrel attachment area is usually due to
emission of thread lubricant used during assembly of the barrel at the factory, or by slight gas
leakage which stops after the cylinder has been in service for a while. This condition is neither
harmful nor detrimental to engine performance and operation. If it can be proven that leakage
exceeds these conditions, the cylinder must be replaced.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов