manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

V - SURFACE CONTROLS

07/15/06

1H14

15. Install the seat belts removed from the top of the floor tunnel and secure with bolt, washer and

nut.

16. Install the floor panel and seat belt attachments aft of the main spar, and secure panel with

screws.

17. Install the aft floor tunnel and secure with screws.

18. Install the carpet over the aft floor tunnel.

19. Install the trim plate on top of the forward end of the aft floor tunnel. 

c.

Install the panel to the aft section of the airplane and the seats.

5-19.

REMOVAL OF STABILATOR TRIM CONTROLS (AFT). (Refer to Figure 5 -8. ) 

a.

Remove the access panel to the aft section of the fuselage. 

b.

Block the trim cables at the first set of pulleys (35) forward of the cable turnbuckles (10 and 11) in
the aft section of the fuselage by a method shown in Figure 5-7. 

c.

Disconnect the cable (12) at the turnbuckles (10 and 11) in the aft section of the fuselage. 

d.

Remove the tail cone by removing its attachment screws. 

e.

Disconnect the link (25) between the trim screw (23) and the trim control arm (28) by removing the
nut, washer and bolt (24) that connects the link to the screw. 

f.

Remove the cotter pin from the top of the screw (23), and turn the screw down and out of the barrel
(20).

g.

Remove the snap ring (32), washer (31) and thrust washer (30) from the bottom of the barrel. 

h.

Disconnect the diagonal rib (22) from the horizontal rib (16) that supports the trim assembly by
removing the four attachment nuts, washers and bolts. 

i.

Draw the trim cable (12) from the fuselage.

5-20.

INSTALLATION OF STABILATOR TRIM CONTROLS (AFT). (Refer to Figure 5-8.) 

a.

Wrap the trim barrel (20) by first laying the center (as measured equally from each end to the center
of the cable) of the trim cable (12) in the slot of the barrel. Bring the upper cable through the
diagonal slot in the flange at the upper end of the barrel and wrap down in a counter -clockwise
direction. Bring the lower cable through the diagonal slot in the lower end of the barrel and wrap up
in a clockwise direction. Wrap the cable as evenly as possible to obtain 23 wraps on the barrel as
viewed from the side opposite the slot and with the cables extending out from the slotted side. 

b.

Block both cables by clamping them between two pieces of wood laid next to the wraps to prevent
them from unwrapping. 

c.

Ascertain that the barrel bushings (19 and 29) are installed in the rib plate (17) and clip (21). 

d.

Lubricate the bushings and install the trim barrel (20) in the bushings between the two support ribs.
Attach the bottom diagonal rib (22) to horizontal rib (16) and secure with bolt, washers and nuts. 

e.

Install the thrust washer (30), washer (31) and snap ring (32) on the lower end of the barrel. 

f.

Install the trim screw (23) in the barrel (20) and secure each end with a cotter pin through the screw. 

g.

Route the cables into the fuselage and attach the ends to the forward trim cables (8 and 9). 

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

ICARO JET Manual preview
JET
Бренд: ICARO Страницы: 17
Skywalk PEPPER CROSS LIGHT Manual preview
PEPPER CROSS LIGHT
Бренд: Skywalk Страницы: 12
PSA CRJ-900 Maintenance Manual preview
CRJ-900
Бренд: PSA Страницы: 13
Mcc Aviation AROLLA 2 Owner'S Manual preview
AROLLA 2
Бренд: Mcc Aviation Страницы: 15
Amewi AMX PLANES TASMAN STOL 1500mm Manual preview
AMX PLANES TASMAN STOL 1500mm
Бренд: Amewi Страницы: 28
P.AP. Team THOR130 Use And Maintenance Manual preview
THOR130
Бренд: P.AP. Team Страницы: 12
Dyn'Aéro MCR 4S Flight Manual preview
MCR 4S
Бренд: Dyn'Aéro Страницы: 39
Cabrinha Kites CROSSBOW 2006 User Manual preview
CROSSBOW 2006
Бренд: Cabrinha Kites Страницы: 56
Van's Aircraft RV-12 Pilot Operating Handbook preview
RV-12
Бренд: Van's Aircraft Страницы: 99
Raytheon Beechcraft Bonanza 35 Series Shop Manual preview
Beechcraft Bonanza 35 Series
Бренд: Raytheon Страницы: 493
CEAPR DR400/120D Pilot Operating Handbook preview
DR400/120D
Бренд: CEAPR Страницы: 104
Tutti Bambini GC 35 Assembly Instructions Manual preview
GC 35
Бренд: Tutti Bambini Страницы: 12
Niviuk ARTIK 5 User Manual preview
ARTIK 5
Бренд: Niviuk Страницы: 27
Niviuk TAKOO 3 User Manual preview
TAKOO 3
Бренд: Niviuk Страницы: 22
NIVIUK GLIDERS IKUMA 21 User Manual preview
IKUMA 21
Бренд: NIVIUK GLIDERS Страницы: 25
Niviuk PEAK 23 User Manual preview
PEAK 23
Бренд: Niviuk Страницы: 20
NIVIUK GLIDERS PEAK 5 User Manual preview
PEAK 5
Бренд: NIVIUK GLIDERS Страницы: 27
Niviuk SKIN 2 P User Manual preview
SKIN 2 P
Бренд: Niviuk Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды