manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию

Получите свой бесплатный сервисный мануал для Piper Cherokee LANCE на manualshive.com. Скачайте полное руководство пользователя для вашего самолета, чтобы быть уверенным в его безопасной эксплуатации. Надежное руководство поможет вам летать с удовольствием и уверенностью.

Поделиться
Скачать
background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

V - SURFACE CONTROLS

1G23

5-5c.

FLEX JOINT REPLACEMENT (Refer to Figure 5-1c.) 

a.

Carefully lay out location for hole to be drilled in flex joint tube to match hole in control column
shaft.

b.

Using a #5 (0.2055) drill bit, drill hole through flex joint tube at location determined above.

c.

Ream drilled hole, in steps, with a #1 reamer, checking to ensure proper depth for taper pin and
sufficient pin thread protrusion for proper installation.

NOTE: Reamer may be purchased from Enstice Tool Co., Palm Bay, Florida.

d.

Install pin through tube and shaft.

1.

If pin shoulder does not protruded past sprocket hub, install an AN960-10 washer

2.

If pin shoulder does protruded past sprocket hub, install an AN975-3 washer

3.

Install nut. Torque 35 - 40 inch-pounds.

5-6. AILERON CONTROLS.

5-7. REMOVAL OF AILERON CONTROL CABLES. (Refer to Figure 5-2.) 

a.

For the removal of any of the control cables in the fuselage or wings, first remove the floor panel
that is located directly aft of the main spar by removing the center seats, seat belt attachments and
the screws securing the panel. Lift the panel and remove from airplane. 

b.

To remove either the right or left primary control cables (14 and 15) that are located in the fuselage,
the following procedure may be used:

1.

Remove the fuel selector panel cover by removing the rudder trim knob and the cover
attachment screws.

2.

Remove the lower selector cover and disconnect the fuel selector control lever from the
selector torque tube by removing the attachment pin located at the bottom of the lever.

3.

Remove the tunnel plate just aft of the tee bar by laying back enough tunnel carpet to remove
the plate attachment screws.

4.

Remove the forward heat duct from one side of the floor tunnel (preferably from the side from
which the cable is to be removed) by removing the trim control wheel cover, the heater baffles
from the side of the duct, the floor carpet and the duct attachment screws.

5.

Separate the primary control cable (14 or 15) at the turnbuckle (12 or 16) located in the floor
opening aft of the main spar.

6.

Remove the cable pulleys (8) attached to the lower section of the control column tee bar
assembly by removing the pulley attachment bolt (21).

7.

Move the cable guard (20) located under the pulley cluster (9) below the fuel selector by
removing the cotter pin from the exposed end of the guard and sliding it to the left or right as
required.

8.

Remove the cotter pins used as cable guards at the pulley (10) in the forward area of the floor
opening aft of the main spar.

9.

Disconnect the cable (14 or 15) from the control chain(4) at the control column tee bar
assembly by removing the cotter pin, nut, bolt and bushing (23) that connect the two together.
Secure the chains in some manner to prevent them from unwrapping from around the
sprockets.

10. Draw the cable back through the floor tunnel. 

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Textron Cessna 208B Service Bulletin preview
Cessna 208B
Бренд: Textron Страницы: 34
SKY PARAGLIDERS Flux L 2017 User Manual preview
Flux L 2017
Бренд: SKY PARAGLIDERS Страницы: 51
Sky Country DISCOVERY 3 Manual preview
DISCOVERY 3
Бренд: Sky Country Страницы: 19
SOL paragliders Hercules 380 Manual preview
Hercules 380
Бренд: SOL paragliders Страницы: 15
SOL paragliders ATMUS 2 Paraglider'S Manual preview
ATMUS 2
Бренд: SOL paragliders Страницы: 23
Sol KANGAROO Operator'S Manual preview
KANGAROO
Бренд: Sol Страницы: 22
SOL paragliders Attak Manual preview
Attak
Бренд: SOL paragliders Страницы: 26
SOL paragliders ELLUS 2 Pilot'S Manual preview
ELLUS 2
Бренд: SOL paragliders Страницы: 39
HPH Glasflugel 304 eS Manual preview
Glasflugel 304 eS
Бренд: HPH Страницы: 53
HPH Glasflugel 304 C Flight Manual preview
Glasflugel 304 C
Бренд: HPH Страницы: 64
Jabiru J230-C Service Manual preview
J230-C
Бренд: Jabiru Страницы: 171
Hornet FIREBIRD Manual preview
FIREBIRD
Бренд: Hornet Страницы: 78
SKY PARAGLIDERS atis 3 Manual preview
atis 3
Бренд: SKY PARAGLIDERS Страницы: 37
Ozone ZENO 2 Pilot'S Manual preview
ZENO 2
Бренд: Ozone Страницы: 34
Aeros Combat 09 13.7 Manual preview
Combat 09 13.7
Бренд: Aeros Страницы: 8
Icarus NANO 106 Owner'S Manual preview
NANO 106
Бренд: Icarus Страницы: 36
Textron SB750-55-10 Service Bulletin preview
SB750-55-10
Бренд: Textron Страницы: 22
Textron Cessna Citation CJ3 Operation Manual preview
Cessna Citation CJ3
Бренд: Textron Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды