manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию, Страница: 303 / 854

Поделиться
Скачать
Piper Cherokee LANCE Скачать руководство пользователя страница 303

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

07/15/06

VIA - LANDING GEAR AND BRAKE SYSTEM

(PA-32R-300)

2C11

g.

Lubricate the inner wall of the cylinder (23) with hydraulic fluid. Carefully insert the piston tube
assembly into the bottom of the cylinder, allowing the orifice tube to guide itself into the fork tube,
until the snap ring (38) can be installed in the annular slot at the bottom of the cylinder. Install
wiper strip (36), slide washer (37) into position and secure assembly with snap ring (38). 

h.

At the top of the cylinder (23), tighten (torque) the orifice tube locknut (16). 

i.

Ascertain that bushings are installed in the upper and lower torque links (24 and 26) and then install
both links. The torque link bolt assemblies should be lubricated and installed with the flat of the
bolt head hex adjacent to the milled stop on the wide end of the link. Tighten the bolts only tight
enough to allow no side play in the link, yet be free enough to rotate. 

j.

Ascertain that the upper and lower oleo housing bushings (20 and 22) are installed if reusing
original housing. If new housing is being installed, bushings are not to be used or the installation
attempted. Install the cylinder into the oleo housing, position spacer washer(s) (43) over the top of
the cylinder and secure with snap ring (17). Install spacer washers as required to obtain .0 to .015 of
an inch thrust of the cylinder within the housing. 

k.

At the top of the oleo housing, install on the cylinder the aligner guide bracket (12) and steering
arm (11). Install cap bolts (1), tighten 20 to 25 inch-pounds torque and safety with MS20995C40
wire (2). 

1.

Install the shimmy dampener and safety. 

m.

Lubricate the gear assembly. (Refer to Lubrication Chart, Section II). 

n.

Compress and extend the strut several times to ascertain that the strut will operate freely. Weight of
the gear wheel and fork should allow the strut to extend. 

o.

Service the oleo strut with fluid and air. (Refer to Oleo Struts, Section II.) 

p.

Check nose gear for alignment (refer to Paragraph 6A-13) and gear operation.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов