Piper Cherokee LANCE страница 837 Скачать руководство пользователя | Manualshive

Страница: 837 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

03/27/08

III - INSPECTION

4H1

9.

Unscheduled Maintenance Checks

WARNING: FAILURE TO CONSULT APPLICABLE VENDOR PUBLICATION(S), WHEN

SERVICING OR INSPECTING VENDOR EQUIPMENT INSTALLED IN PIPER
AIRCRAFT,

MAY RENDER THE AIRCRAFT UNAIRWORTHY. (SEE

INTRODUCTION - SUPPLEMENTARY PUBLICATIONS.)

The following inspections are required in response to specific anomalies encountered during aircraft
operation. Note that the items listed herein are guidelines based on past operating experience. Each
operator should closely monitor his own unique operating conditions/environment and react accordingly
to keep his aircraft airworthy.

NOTE: A log book entry should be made upon completion of any inspections.

A.

Lightning Strike

Item

Inspection

Inspection Interval

Propeller.

Hartzell Propellers - refer to the

Each occurrence,

inspection requirements in the

before further flight.

latest revision of
Hartzell Manual No. 115N.
McCauley Propellers - see latest
revision of: McCauley SB 177.

Engine.

See latest revisions of appropriate

Each occurrence,

Lycoming Service Bulletins

before further flight.

and Overhaul Manual.

Electrical and Avionics

Inspect and check harness, connections,

Each occurrence,

Systems.

and equipment for high voltage damage,

before further flight.

burns and insulation degradation.
Replace or overhaul as required.
Consult with appropriate avionics
vendor(s) for inspections and operational
checks. Bench test alternator and
voltage regulator(s), (see Section X).

All exterior surfaces, skins,

Inspect for burns, evidence of arcing,

Each occurrence,

and structure.

and damage on surfaces and bearings.

before further flight.

Check for correct material properties in
the area of the strike path. Degauss
engine mount. Replace or repair
affected areas/parts.

System Components.

Inspect instrumentation, vacuum,

Each occurrence,

pitot/static, and fuel systems,

before further flight.

for damage and correct operation.

Static Wicks.

Replace.

Each occurrence,
before further flight.

«
...
835
836
837
838
839
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: Gin Страницы: 34

Бренд: Cessna Страницы: 242

Бренд: Wowings Страницы: 17

Бренд: Heli-Max Страницы: 24

Бренд: SKY PARAGLIDERS Страницы: 28

Бренд: Guldmann Страницы: 36

SQUARE Light 90

Бренд: ICARO Страницы: 14

Бренд: Ozone Страницы: 20

Бренд: Diamond Aircraft Страницы: 24

Бренд: Sky Country Страницы: 28

Бренд: Rompa Страницы: 11

Super Pulsar 100

Бренд: Pulsar Aircraft Corporation Страницы: 32

Бренд: Airbus Страницы: 7

Бренд: AirBorne WindSports Страницы: 35

Бренд: AirBorne WindSports Страницы: 96

EDGE XT 912 L ARROW K MICROLIGHT

Бренд: AirBorne WindSports Страницы: 112

Бренд: Airbus Страницы: 211

Zodiac 601XL SLSA

Бренд: AMD Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды