manualshive.com logo in svg

Piper Cherokee LANCE, Руководство по обслуживанию, Страница: 748 / 854

Поделиться
Скачать
Piper Cherokee LANCE Скачать руководство пользователя страница 748

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

III - INSPECTION

07/15/06

4C14

6.

Inspection Requirements

WARNING: INSTRUCTIONS FOR CONTINUED AIRWORTHINESS (ICA) FOR ALL NON-PIPER

APPROVED STC INSTALLATIONS ARE NOT INCLUDED IN THIS MANUAL.
WHEN A NON-PIPER APPROVED STC INSTALLATION IS INCORPORATED ON
THE AIRPLANE, THOSE PORTIONS OF THE AIRPLANE AFFECTED BY THE
INSTALLATION MUST BE INSPECTED IN ACCORDANCE WITH THE ICA
PUBLISHED BY THE OWNER OF THE STC. SINCE NON-PIPER APPROVED STC
INSTALLATIONS MAY CHANGE SYSTEMS INTERFACE, OPERATING
CHARACTERISTICS AND COMPONENT LOADS OR STRESSES ON ADJACENT
STRUCTURES, THE PIPER PROVIDED ICA MAY NOT BE VALID FOR AIRPLANES
SO MODIFIED.

A.

Annual / 100 Hour Inspection. (See paragraph 7.)

Owners/operators may maintain the airplane solely under FAR 91.409 (a) and (b) inspection
requirements. The 100 hour inspection cycle is a complete inspection of the airplane and is identical
in scope to an annual inspection. Inspections must be accomplished by persons authorized by the
FAA.

B.

Progressive Inspection. 

The Progressive Inspection program is designed to permit the best utilization of the aircraft through
the use of a planned inspection schedule. This schedule is prepared in a manual form, which will be
available from Piper Dealers:

P/N 767-019 for the Piper PA-32-260/300 (S/N's 32-1 & up), and 

P/N 767-018 for the Piper PA-32R-300 (S/N's 32R-7680003 & up).

Refer to Piper's Customer Service Information Aerofiche P/N 1753-755 for a checklist to ensure
obtaining latest issue.

NOTE: The 50 Hour Progressive Inspection Manuals (P/N’s 767-018 and 767-019) referenced

above will not be stand-alone documents. They will consitute snapshots of the
Airworthiness Limitations and Inspection sections of the Instructions for Continued
Airworthiness (ICA) and will be current only at the time of printing. Use them as follows:

(1) Owners/operators desiring to establish a Part 91 Progressive Inspection Program

(PIP) (see 91.409(d)) or a Part 135 Approved Aircraft Inspection Program (AAIP)
(see 135.419) should use the appropriate Progressive Inspection Manual as a
template for submission to their regional FAA office.

(2) Service centers conducting Event Cycle inspections under a FAA-approved PIP or

AAIP can use the appropriate Progressive Inspection Manual as a working check-off
list/form, provided they verify its currency against the FAA-approved PIP or AAIP.

C.

Overlimits Inspection.

If the airplane has been operated so that any of its components have exceeded their maximum
operational limits, special inspections may be required by Piper and/or the component
manufacturer. See Unscheduled Maintenance Checks and applicable vendor publications.

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов