Piper Cherokee LANCE Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 854

Piper Cherokee LANCE Скачать руководство пользователя страница 50

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

II - HANDLING AND SERVICING

03/27/08

1C2

NOTE: If using an external battery and the airplane's battery is low or depleted, disconnect the

airplane battery at the negative terminal to prevent excessive loading of the external battery.

c.

Insert the plug of the jumper cable into the receptacle.

d.

Set MASTER SWITCH to ON and proceed with NORMAL engine starting.

e.

After starting engine, set the MASTER SWITCH to OFF and remove the jumper cable plug from
the receptacle.

f.

Set the MASTER SWITCH to ON and check the alternator ammeter for an indication of output.

WARNING: DO NOT ATTEMPT FLIGHT WITHOUT AN INDICATION OF ALTERNATOR

OUTPUT.

NOTE: If the aircraft battery is weak, charging current will be high. Do not take off until charging

current falls below 20 amperes. Do not take off with a completely discharged battery as
three-volts are needed to excite the alternator.

2-25. CLEANING.

2-26. CLEANING EXTERIOR SURFACES. The airplane should be washed with a mild soap and water.

Harsh abrasive or alkaline soaps or detergents used on painted or plastic surfaces could make scratches
or cause corrosion of metal surfaces. Cover areas where cleaning solution could cause damage. To wash
the airplane, the following procedure may be used:

a.

Flush away loose dirt with water.

b.

Apply cleaning solution with a rag, sponge or soft bristle brush.

c.

To remove stubborn oil and grease, use a cloth dampened with naphtha.

d.

Where exhaust stains exist, allow solution to remain on the surface longer.

e.

Any good automotive wax may be used to preserve the painted surfaces. Soft cleaning cloths or a
chamois should be used to prevent scratches when cleaning or polishing. A heavier coating of wax
on the leading surfaces will reduce the abrasion problems in these areas.

2-27. CLEANING ENGINE COMPARTMENT. Before cleaning the engine compartment, place a strip of

tape on the magneto vents to prevent any solvent from entering these units.

a.

Place a pan under the engine to catch waste.

b.

With the engine cowling removed, spray or brush the engine with solvent or a mixture of solvent
and degreaser, as desired. Brushing after spraying may be necessary to remove heavy grease and
dirt deposits.

CAUTION: DO NOT SPRAY SOLVENT INTO THE ALTERNATOR, STARTER, AIR INTAKE,

AND ALTERNATE AIR INLETS.

c.

Allow the solvent to remain on the engine from five to 10 minutes, then rinse the engine clean with
additional solvent and allow to dry.

CAUTION: DO NOT OPERATE ENGINE UNTIL EXCESS SOLVENT HAS EVAPORATED OR

OTHERWISE BEEN REMOVED.

d.

Remove the protective covers from the filter and magnetos.

e.

Lubricate controls, bearing surfaces, etc., per Lubrication Chart.

«
...
48
49
50
51
52
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов