Piper Cherokee LANCE страница 719 Скачать руководство пользователя | Manualshive

Страница: 719 / 854

background image

PIPER CHEROKEE SIX / LANCE SERVICE MANUAL

INTRODUCTION

1.

Instructions for Continued Airworthiness

WARNING: INSTRUCTIONS FOR CONTINUED AIRWORTHINESS (ICA) FOR ALL NON-PIPER

APPROVED STC INSTALLATIONS ARE NOT INCLUDED IN THIS MANUAL.
WHEN A NON-PIPER APPROVED STC INSTALLATION IS INCORPORATED ON
THE AIRPLANE, THOSE PORTIONS OF THE AIRPLANE AFFECTED BY THE
INSTALLATION MUST BE INSPECTED IN ACCORDANCE WITH THE ICA
PUBLISHED BY THE OWNER OF THE STC. SINCE NON-PIPER APPROVED STC
INSTALLATIONS MAY CHANGE SYSTEMS INTERFACE, OPERATING
CHARACTERISTICS AND COMPONENT LOADS OR STRESSES ON ADJACENT
STRUCTURES, THE PIPER PROVIDED ICA MAY NOT BE VALID FOR AIRPLANES
SO MODIFIED.

The PIPER PA-32-260/300 / PA-32R-300 (Cherokee Six / Lance) Service Manual constitutes the
Instructions for Continued Airworthiness in accordance with Federal Aviation Regulations (FAR) Part
23, Appendix G. Section I contains the Airworthiness Limitations and the Inspection Program is in
Section III.

2.

General

This publication is prepared in PIPER proprietary format with respect to arrangement and content.

WARNING: USE ONLY GENUINE PIPER PARTS OR PIPER APPROVED PARTS OBTAINED

FROM PIPER APPROVED SOURCES,

IN CONNECTION WITH THE

MAINTENANCE AND REPAIR OF PIPER AIRPLANES.

This manual generally does not contain hardware callouts for installation. Hardware callouts are only
indicated where a special application is required. To confirm the correct hardware used, refer to the
PA-32-260/300/PA-32R-300 Parts Catalog, P/N 753-689, and FAR 43 for proper utilization.

Genuine PIPER parts are produced and inspected under rigorous procedures to insure airworthiness and
suitability for use in PIPER airplane applications. Parts purchased from sources other than PIPER, even
though identical in appearance, may not have had the required tests and inspections performed, may be
different in fabrication techniques and materials, and may be dangerous when installed in an airplane.

Additionally, reworked or salvaged parts or those parts obtained from non-PIPER approved sources, may
have service histories which are unknown or cannot be authenticated, may have been subjected to
unacceptable stresses or temperatures or may have other hidden damage not discernible through routine
visual or nondestructive testing. This may render the part, component or structural assembly, even
though originally manufactured by PIPER, unsuitable and unsafe for airplane use.

PIPER AIRCRAFT, INC. expressly disclaims any responsibility for malfunctions, failures, damage or
injury caused by use of non-PIPER approved parts.

NOTE: PIPER AIRCRAFT, INC. expressly reserves the right to supersede, cancel and/or declare

obsolete any part, part numbers, kits or publication that may be referenced in this manual
without prior notice.

In any question concerning the care of your airplane, be sure to include the airplane serial number in any
correspondence.

03/27/08

INTRODUCTION

4A7

«
...
717
718
719
720
721
...
»

Содержание Cherokee LANCE























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cherokee LANCE

Бренд: MAULE Страницы: 31

Бренд: Raytheon Страницы: 8

Бренд: Xtim Страницы: 12

Бренд: Topmodel Страницы: 27

Бренд: 3D Hobby Shop Страницы: 20

Бренд: Sky Country Страницы: 13

Бренд: MAC PARA Страницы: 18

Бренд: iKarus Страницы: 73

1.8M Bleriot XI

Бренд: Dancing Wings Hobby Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды