149
A
ppe
ndi
x
NA
VI/
A
V
Your vehicle is operating in Simple
hybrid mode.
Connect the speed signal input (pink
lead wire) of the power cable cor-
rectly, and reset the 3D Hybrid Sen-
sor memory (“
Learning Status
”).
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Confirm the installation angle. (The
navigation system must be installed
within the allowed installation angle.
For details, refer to “Installation Man-
ual”.)
Indication of the position of your vehi-
cle is misaligned after a U-turn or
reversing.
Check whether or not the reverse
gear signal input lead (Violet) is con-
nected properly. (The navigation sys-
tem works properly without the lead
connected, but positioning accuracy
will be adversely affected.)
The map continually reorients itself.
The traveling direction is set to Head-
ing Up.
Touch
on the screen and change
the map display.
Tracking marks are not displayed.
The “
Tracking Display
” is turned
off.
Check the “
Tracking Display
” set-
tings (
➞
Page 75) and make sure
“
Always
” or “
This Trip
” is selected.
The daylight display is used even
when the vehicle lights are on.
“
Daytime
” is set to “
Day/Night Dis-
play
”.
Check the “
Day/Night Display
” set-
ting (
➞
Page 75) and make sure
“
Nighttime
” is selected.
The orange/white lead is not con-
nected.
Check the connection.
The system will not switch on or will
not operate.
Installation or connection has been
carried out incorrectly.
Check with your dealer.
The display is very dim.
The vehicle’s light is turned ON, and
“
Nighttime
” is selected on “
Day/
Night Display
”.
Read about the “
Day/Night Dis-
play
” setting (
➞
Page 75) and, if
desired, select “
Daytime
”.
The vehicle cabin temperature is
extremely low.
A Liquid Crystal Display (LCD) is
used, and such displays tend to
darken when cold. Wait for the vehi-
cle to warm up.
Picture quality adjustment of the dis-
play is not correct.
Refer to “Operating the Picture
Adjustment” to adjust the picture
quality.
No sounds are heard.
The volume level will not rise.
The volume level is low.
Adjust the volume level.
The attenuator or mute is on.
Turn the attenuator or mute off.
The speaker lead is disconnected.
Check the connection.
Adjusting the volume of navigation
guidance and beeps is not possible.
You cannot adjust them with the
VOLUME
knob.
Turn the volume up or down accord-
ing to “
Volume
” (
➞
Page 73) in the
“
Settings
” menu.
A strange sound is heard when the
vehicle comes close to a certain
place. (E.g. Dog barking)
The sound for the entry of “
Address
Book
” is set.
Set the sound setting of that entry to
“
No Sound
”. (
➞
Page 57)
Slope
is not displayed on the
Vehicle Dynamics
screen.
Inclination
does not move on the
3D
Calibration
screen.
The speed pulse lead is not con-
nected.
Connect the speed pulse lead.
The person on the other end of the
phone call cannot hear the conversa-
tion due to an echo.
The voice from the person on the
other end of the phone call is output
from the speakers and then picked
up by the microphone again, creat-
ing an echo.
Use the following methods to reduce
the echo.
— Lower the volume on the receiver
— Have both speakers pause
slightly before speaking
Symptom
Cause
Action (See)
Содержание AVIC N4 - Navigation System With DVD player
