Chapter 3 - Powering on the Mosport 1TE/2TE
IP Address Discovery or Configuration
16
Mosport 1TE/2TE
3.
Power on the PCs.
Your computers do not have to be turned on for the telephone or fax services.
You can now access the Mosport 1TE/2TE web interface. Refer to the
Software Configuration
Guide
for more details.
Initial Provisioning Sequence
When starting the Mosport 1TE/2TE for the first time, it needs to be configured before it can support calls. This
process is known as
provisioning
. This sequence assumes that you have installed the Mosport 1TE/2TE
hardware as per
“Hardware Installation” on page 14
.
The Mosport 1TE/2TE requests its configuration only on the first restart. You can change the configuration at
will after the initial provisioning and the provisioning system can refresh the Mosport 1TE/2TE configuration.
Initial provisioning sequence:
1.
When the Mosport 1TE/2TE starts, it broadcasts a message requesting DHCP services (if the unit
is configured to start in DHCP mode).
2.
The DHCP server responds with a set of WAN IP addresses and network parameters, one of which
is the Mosport 1TE/2TE WAN IP address.
The following are some of the network parameters assigned via DHCP:
•
Mosport 1TE/2TE WAN IP address
•
Subnet Mask
•
Default Router IP address
•
DNS IP addresses
•
Configuration script server IP address and port number (optional)
•
SIP Servers IP address and port number
3.
The Mosport 1TE/2TE request its configuration by using a configuration file.
Default Static WAN IP Address Configuration
If there is no DHCP server in your network, then the WAN IP address has to be configured statically.
To start the Mosport 1TE/2TE with a static WAN IP address:
1.
Power on the Mosport 1TE/2TE by flipping the power switch. If this is the very first time you are
installing the Mosport 1TE/2TE, it will restart twice.
2.
Reconfigure the IP address of your computer to
192.168.0.11
and the Subnet Mask to
255.255.255.0
. Restart the computer.
3.
Power on the PCs.
Your computers do not have to be turned on for the telephone or fax services.
4.
Insert a small, unbent paper clip into the
RESET/DEFAULT
hole located at the rear of the Mosport
1TE/2TE.
The
Power
LED will start blinking, and after a few seconds, all the LEDS will start blinking. Release
the paper clip after all the LEDs start blinking and before they all stop blinking (between 7-11
seconds).
This procedure is called a partial reset. After a partial reset is performed, the Mosport 1TE/2TE uses
the default WAN IP address 192.168.0.1/24. Refer to
“Partial Reset” on page 20
for details on the
partial reset procedure.
You can now access the Mosport 1TE/2TE web interface. Refer to the
Software Configuration
Guide
for more details.
Содержание Mosport 1E-F
