PEUGEOT Django 125 Скачать руководство пользователя страница 42

Страница: 42 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Reassembly:

- Proceed in reverse order to disassembly and do

not grease the bearings.

When refitting, respect the way the rollers
are installed.

- Grease the moving flange bore lightly (high

temperature grease).

Checking the thickness of the clutch

linings

- Using the depth calliper, measure the thickness

of the clutch linings.

Mini. thickness: 2 mm.

The balance of the clutch jaw assembly is
factory set, and therefore the assembly
cannot be dismantled.

Removal of the clutch lining assembly

- Compress the clutch and driven pulley assembly

using tool 758008 equipped with the protection
spacer P/N 801682.

- Remove nut (1) using spanner P/N 752361.

752361.

- Slacken tool P/N 758008.

752361

801682

758008

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды