PEUGEOT Django 125 Скачать руководство пользователя страница 28

Страница: 28 / 83

BODY PANELS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Remove the footboard by sliding it towards the

rear of the vehicle and then lifting it.

• 2 washer head screws (A).

• 2 washer head screws Ø6 mm (B).

• 3 washer head screws Ø6 mm (C).

Removal of the rear shield panel

Procedure 13.

- Remove the front shield panel. See:

Procedure 9.

page 23.

- Remove the footboard. See: Procedure 12.

page 26.

- Open the tank filler cap door.
- Remove the tank filler cap.
- Disconnect the accessory plug.
- Remove the rear shield panel.

• 4 plastic screws (A).

• 2 washer head screws (B).

Removal of the door-locking system

Procedure 14.

- Remove the rear shield panel. See:

Procedure 13. page 27.

- Remove the RH or LH door locking pin (1) and

its cable by turning it through a 1/4 turn.

- Remove the double-acting control plate (2).

• 3 plastic screws.

- Push back the locking ratchet (A) and extract

the barrel from the rear shield panel.

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды