PEUGEOT Django 125 Скачать руководство пользователя страница 35

Страница: 35 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Remove the air filter unit through the under-

saddle storage compartment space. (1 collar and
1 screws)

Use a cloth to protect the cover of the air
unit.

Take care not to damage the throttle
control when bringing out the air unit.

- Disconnect the relay box air vent hose (1).
- Disconnect the oil vapour return pipe (2).

- Remove the air filter cover (9 bolts) and its seal.
- Remove the inlet silencer drain plug to let

humidity and oil drip out (3).

- Remove the air filter (4).
- Clean inside the air filter box.
- Clean the oil vapour return filter (5).

Reassembly

- Fit a new air filter.
- Fit the gasket.
- Install the air filter cover.

Removal of the spark plug

- The engine must be cold.
- Open the saddle.
- Remove the access door.

• 1 screw.

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды