manualshive.com logo in svg

PEUGEOT Django 125, Руководство по ремонту

PEUGEOT Django 125 - это стильный складной скутер для городских поездок. Для обслуживания и ремонта вы можете скачать бесплатное Workshop Manual на нашем сайте. Этот документ содержит подробное руководство по эксплуатации, диагностике и ремонту вашего скутера. Скачайте его сейчас с manualshive.com.

Поделиться
Скачать
background image

TABLE OF CONTENTS

2

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Removal of the grab handles ................................................................................................................... 22

Removal of the upper side fairing assembly ............................................................................................ 23

Removal of the upper side fairing assembly ............................................................................................ 23

Removal of the front shield panel............................................................................................................. 23

Removal of the head light fairing ............................................................................................................. 25

Removal of the speedometer fairing ........................................................................................................ 26

Removal of the footboard......................................................................................................................... 26

Removal of the rear shield panel ............................................................................................................. 27

Removal of the door-locking system ........................................................................................................ 27

Removal of a RH or LH door....................................................................................................................28

Removal of the RH or LH under body panel ............................................................................................ 28

Removal of the front mudguard ............................................................................................................... 29

Removal of the dirt shield ........................................................................................................................ 30

SERVICE OPERATIONS................................................................................................................................. 31

Empty the oil from the engine .................................................................................................................. 31

Draining the relay box .............................................................................................................................. 32

Replacing the air filter with transmission maintenance ..................................................................................... 33

Reassembly....................................................................................................................................................... 33

Replacing the air filter without transmission maintenance ................................................................................ 33

Reassembly....................................................................................................................................................... 34

Removal of the spark plug ....................................................................................................................... 34

Idle setting................................................................................................................................................ 35

Removal of the primary transmission cover............................................................................................. 36

Removal of the starter system........................................................................................................................... 36

Fitting the starter system ................................................................................................................................... 38

Removal of the transmission air filter ................................................................................................................ 38

Removal of the drive pulley ...................................................................................................................... 39

Removal of the driven pulley ....................................................................................................................39

Changing the drive pulley bearings.......................................................................................................... 40

Checking the drive belt ............................................................................................................................ 40

Checking the thickness of the clutch linings ............................................................................................ 41

Removal of the clutch lining assembly ..................................................................................................... 41

Refitting the clutch lining assembly .......................................................................................................... 42

Installing the primary drive ....................................................................................................................... 43

Installing the valve clearance................................................................................................................... 44

Checking the valve clearance .................................................................................................................. 46

Changing the fuel filter .............................................................................................................................46

Integral braking ........................................................................................................................................ 47

Brake pad wear ........................................................................................................................................ 47

Front brake ........................................................................................................................................................47

Rear brake......................................................................................................................................................... 48

Содержание Django 125




















































































Отзывы:

Нет отзывов

Похожие инструкции для Django 125

Razor E Prime Manual preview
E Prime
Бренд: Razor Страницы: 28
NAVEE FN-E1 User Manual preview
FN-E1
Бренд: NAVEE Страницы: 16
Malaguti Madison3 125 Owner'S Manual preview
Madison3 125
Бренд: Malaguti Страницы: 272
Wuyi Chuangxin Metal Tools I1 Manual preview
I1
Бренд: Wuyi Chuangxin Metal Tools Страницы: 12
Motus 10 sport pro Original User Manual preview
10 sport pro
Бренд: Motus Страницы: 20
Motus Pro 10 Sport Original User Manual preview
Pro 10 Sport
Бренд: Motus Страницы: 53
Shoprider Altea SL7-3 Specifications preview
Altea SL7-3
Бренд: Shoprider Страницы: 1
Kaabo Mantis User Manual preview
Mantis
Бренд: Kaabo Страницы: 21
Scooty DRIVE PRO Original Instructions Manual preview
DRIVE PRO
Бренд: Scooty Страницы: 22
Radio Flyer Color FX EZ Glider Manual preview
Color FX EZ Glider
Бренд: Radio Flyer Страницы: 6
Handicare HIPPO Service Manual preview
HIPPO
Бренд: Handicare Страницы: 28
Yvolve Sports Neon Vector Manual preview
Neon Vector
Бренд: Yvolve Sports Страницы: 30
Jetson ESBT-V5 User Manual preview
ESBT-V5
Бренд: Jetson Страницы: 14
Yamaha MAJESTY YP250A Owner'S Manual preview
MAJESTY YP250A
Бренд: Yamaha Страницы: 116
Razor PowerWing DLX Manual preview
PowerWing DLX
Бренд: Razor Страницы: 36
Tempish IGNIS 125 Instructions Manual preview
IGNIS 125
Бренд: Tempish Страницы: 18
Bravo EV EVT- 4000e Service Manual preview
EVT- 4000e
Бренд: Bravo EV Страницы: 45
Bravo EVT-168 Service Manual preview
EVT-168
Бренд: Bravo Страницы: 59

Бренды по названию

Популярные бренды

Загрузить еще бренды