PEUGEOT Django 125 Скачать руководство пользователя страница 78

Страница: 78 / 83

ELECTRICITY

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Checking the indicators

- Removing an indicator.
- Connect the indicator in series with a battery

and a ammeter.

Normal consumption: 0.30 - 0.40 A.

- If consumption is outside this range, change the

indicator.

- Carry out the same operation with the other

indicators.

- If the consumption of the indicators is correct,

check the wiring harness.

Checking the red light, the stop light and

the side light

- Remove the side light or the rear light.

1. Connect the side light in series with a

battery and an ammeter.

Normal consumption: 0.25 - 0.35 A.

2. Connect the stop light in series with a
battery and an ammeter.

Normal consumption: 0.25 - 0.35 A.

3. Connect the red light in series with a battery
and an ammeter.

Normal consumption:

0.60 - 0.70 mA.

- If the consumption is outside this range, change

the side light or the rear light.

- If the consumption of the side light or the rear

light is correct:

Check:

• The main harness.
• The stop light contactors.
• The magneto.
• The regulator.

OFF

Ω

20 m

200 m

10A

Ω

COM

OFF

Ω

20 m

200 m

10A

Ω

COM

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды