PEUGEOT Django 125 Скачать руководство пользователя страница 40

Страница: 40 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Removal of the drive pulley

- Remove the upper RH fairing. See: Procedure 6.

page 21

- Removal of the primary transmission cover.

- Hold the fixed flange with tool P/N 752237.
- Remove the nut and the washer.
- Remove the fixed flange.

- Pull the belt aside (1).
- Remove the drive pulley (2) with the guide

hub (3).

Removal of the driven pulley

- Lock the clutch drum (1) with the pin wrench

P/N 752237.

- Remove the nut and the washer.
- Remove the clutch drum, the clutch drive pulley

and driven pulley assembly and belt.

Make a note of the direction of rotation of
the belt.

752237

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды