PEUGEOT Django 125 Скачать руководство пользователя страница 63

Страница: 63 / 83

STEERING/FORK

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Secure the stanchion in a vice fitted with

protection.

- Remove the tightening screw from the internal

tube and its seal (LM).

- If necessary use a mallet to dislodge the

screws.

If the screw is hard to remove, temporarily
refit the spring and the plug. Get someone
to help you and compress the fork unit to
block the calibrated hydraulic tube.

- Remove the calibrated hydraulic tube (D).
- Remove the expansion stop spring (E).

- Separate the fork's tube (F) from the cover (K).

Gently work the tube free from the hollow
shaft whose lip seal, washer and guide ring
should still be in place.

Operation that can be difficult.

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды