PEUGEOT Django 125 Скачать руководство пользователя страница 45

Страница: 45 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Fit the fixed flange (3) to the crank assembly,

ensuring that it is properly positioned on the
crank assembly splines and checking that it is in
contact with the hub guide of the mobile flange.

- Fit the plain washer.
- Hold the fixed flange with tool P/N 752237.
- Fit and tighten the nut.

Tightening torque: 58 Nm.

Installing the valve clearance

- Remove the saddle storage compartment. See:

Range 2. page 20.

- Remove the central fairing under the saddle.

See: Procedure 4. page 21.

- Remove the passenger seat. See: Procedure 1.

page 20.

- Remove the battery cover.
- Disconnect and remove the battery.
- Suspend the rear of the machine.
- Remove the hatch giving access to the shock

absorber upper screw (1).

- Lift the rear of the machine.
- Remove the shock absorber upper fixing bolt.

Tightening torque: 47 Nm.

- Remove the bracket and the driver's saddle (1).

• 2 washer head screws Ø6 mm.
• 2 Ø8 mm screw.

- Remove the central fairing bracket under the

saddle (2).
• 2 Ø6 mm screw.

752237

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды