PEUGEOT Django 125 Скачать руководство пользователя страница 50

Страница: 50 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Remove the brake pad pin (2).
- Remove the brake pads (3).

When refitting the brake pads, push the
pistons all the way into their housing.

After refitting, actuate the brake levers
several times to bring the brake pads
against the brake disc.

Rear brake

When changing the brake pads, it is
essential to replace the brake pad
attachment system (spindle, pin, clips, ...)

- Remove the wheel trim.
- Remove the 5 screws fastening the rear wheel.

Tightening torque: 30 Nm.

- Remove the brake caliper (2 screw).

Tightening torque: 30 Nm.

When refitting the brake caliper, spread
standard thread lock on the bolts.

- Squeeze the caliper holder in order to remove the

first brake pad (1).

- Remove the second brake pad (2).
- Remove the brake pad spring (3).

When refitting the brake pads, push the
pistons all the way into their housing.

After refitting, actuate the brake levers
several times to bring the brake pads
against the brake disc.

GLUE

Содержание Django 125




















































































Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды

PEUGEOT Django 125, Руководство по ремонту

Результаты поиска

Содержание Django 125

Отзывы:

Похожие инструкции для Django 125

Бренды по названию

Популярные бренды