PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 68

Страница: 68 / 74

68 . RamanFlex 400 Series Getting Started Guide

Maintenance

The system does not require regular maintenance other than occasional checking and

cleaning.

Cleaning the Spectrometer and Power Supply Units

WARNING

Switch off the mains voltage and disconnect the mains cord before

cleaning.

You can clean the outside of the spectrometer using a soft, lint-free cloth, moistened if

required with a little water. Mild detergent may be used, if necessary. Do not use abrasive or

solvent-based cleaning materials. Always perform a patch test on an inconspicuous area

before you clean the entire instrument.

Avoid spilling liquid into the instrument. Clean all external spills immediately. If anything that

is spilled enters the main body of the spectrometer, make the instrument inoperative and

then contact a PerkinElmer Service Engineer.

WARNING

Do not directly clean electrical contacts.

WARNING

To avoid any electrical shock hazards, do not allow liquids to run down

into the external PSU. Also, do not allow liquids to run into the

spectrometer. Only use a soft, dry cloth to clean the spectrometer or the

PSU.

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды