PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 16

Страница: 16 / 74

16 . RamanFlex 400 Series Getting Started Guide

Connect the PSU to a three-wire (live, neutral and ground/earth) socket. The ground must be

a non-current carrying wire that is connected to the earth ground at the main distribution

box. The power point (socket) for the instrument PSU should be easily accessible for when

the instrument is serviced.

WARNING

Check the line voltage and frequency of the power point (socket) before

the instrument is connected or the power is switched on. This should be

carried out prior to the installation of the instrument and at any time the

instrument is plugged into a different power point (socket).

Power Cords (Between PSU and Power Outlet Socket)

The power cord supplied to connect the instrument PSU to the power point (socket) should

be appropriate for the country listed as the shipping destination.

WARNING

If the power cord is not appropriate for your country it must be removed

from use immediately and replaced.

If the power cord has any physical damage it must be removed from use

immediately and replaced.

To avoid electrical hazards, the ground pin on the power cord should not

be interfered with in any way.

Fuses

The only fuses that you may have to replace are those in the mains power cords (UK-type

plug only).

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды