PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 12

Страница: 12 / 74

12 . RamanFlex 400 Series Getting Started Guide

Overview

This chapter contains details of the safety precautions. Everyone who is going to install

and/or use the spectrometer must read and follow the precautions before unpacking,

installing or using the instrument.

Before performing any of the operations outlined in this manual, read all of the safety

practices and instructions, and make sure that you understand the procedures explained.

If you do not understand any of the details regarding general safety precautions, please

contact PerkinElmer before proceeding.

All information provided herein is for reference only. All information is believed to be correct

and complete. PerkinElmer shall not be liable for errors contained herein nor damages

concerned with the use of this document. PerkinElmer does not accept liability for the

interpretation of information resulting, either directly or indirectly, from our spectrometers or

associated software interfaces. All results supplied by PerkinElmer’s spectrometers or

software are intended to provide initial determinations and results should be verified or

validated by using other appropriate techniques. All specifications and material contained in

this document are liable to change without notice. All safety information contained in this

document is superseded by governmental safety documents for your district or country; if in

doubt please consult American National Standards Institute’s Z136 series of laser safety

standards.

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды