PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 15

Страница: 15 / 74

Safety Practices . 15

Electrical Safety

The spectrometer module comes assembled within a protective housing to prevent exposure

to electrical hazards. There are also a number of exterior service panels that you should

remove only if you are cleaning the air filters. For more information see

Cleaning the Air

Filters

on page 69.

WARNING

Removal of the protective housing or external panels, other than for

maintenance procedures specifically described in this manual, is

dangerous and is not recommended under any circumstances.

If the protective covers or service panels on the instrument appear to be

damaged, turn the instrument off, secure the instrument against any

unauthorized operation and contact PerkinElmer for advice before using it

again.

WARNING

Electrical hazard

To prevent potential injury to yourself and damage to the instrument,

switch OFF all components in the system and disconnect them from the

line power supply before you alter, or make any new, electrical

connections.

Electrical Protection

Insulation: Class I rating for external circuits. Only connect equipment that meets the

requirements of IEC 61010-1, IEC 60950 or equivalent standards.

Power Supplies

The RamanFlex 400 and RamanFlex 400F are powered by one external PSU. The PSU used

with the spectrometer can adjust automatically to a variety of AC power sources as outlined

in Table 1.
Table 1 PSU input voltages and mains fluctuations information

Input Voltage

Mains Fluctuations

100–230 V AC

±10% of the nominal voltage

NOTE: If you have a deep depletion CCD installed in your RamanFlex, the instrument will be

WARNING

Under no circumstances should you attempt to disassemble the PSU and

carry out repairs. If the PSU has a fault, please contact your PerkinElmer

Service Engineer. The entire unit must be replaced.

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды