Parker PAC Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 197

Parker PAC Скачать руководство пользователя страница 70

PACIO MODULES

70

Parker Automation Controller Installation Guide

PACIO Module Overview

The PACIO Module family consists of a variety of Input and Output modules that are directly connected to
the controller via a high speed EtherCAT network (E-Bus). These include digital or analog I/O Modules,
analog temperature Modules, counters and interface Modules. Each of the PACIO Modules listed in the
table below are compatible with the PAC. See the remainder of this chapter for details about each Module

To order, contact your local Automation Technology Center (ATC) or distributor.

PACIO Module

Part Number

Bus Coupler Modules

PACIO Bus Coupler 3A

PACIO-400-00

Digital Input and Output Modules

PACIO DI16/DO8 1A

PACIO-450-02

PACIO DI16/DO16 1ms/0.5A

PACIO-450-03

PACIO DI8/DO8 1ms/0.5A

PACIO-450-05

PACIO DI16/DO16 1ms/0.5A LS

PACIO-450-13

PACIO DI32 1ms

PACIO-451-02

PACIO DI16 1ms

PACIO-451-03

PACIO DO16 0.5A

PACIO-452-01

PACIO DO8 1A

PACIO-452-02

Analog Input and Output Modules

PACIO AI4-mA 12 Bit

PACIO-441-01

PACIO AI4/8-VDC 13 Bit

PACIO-441-02

PACIO AO4-VDC/mA 12 Bit

PACIO-442-02

Analog Temperature Input Modules

PACIO AI4-Pt/Ni100 16 Bit

PACIO-443-01

PACIO AI4-Pt/Ni1000 16 Bit

PACIO-443-03

PACIO AI8 Thermocouple 16 Bit

PACIO-443-06

Counter Modules

PACIO Counter/Enc

PACIO-454-01

Interface Modules

PACIO PROFIBUS-DP-Slave

PACIO-455-03

PACIO Extender 2 Port

PACIO-400-02

PACIO Accessories

Part Number

PACIO Power Distribution 2X16

PACIO-411-00

PACIO Shield 2x8mm

PACIO-412-01

PACIO Shield 14mm

PACIO-412-02

PACIO 2-Pole Connector

43-026590-01

PACIO 18-Pole Connector

43-026591-01

PACIO 36-pole Connector

43-026592-01

«
...
68
69
70
71
72
...
»

Содержание PAC






































































































































































































Отзывы:

Нет отзывов