Paramount Fitness ME II Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 195

background image

Paramount User Guide

150

|

P a g e

To convert the mechanical hour angle to the sky hour angle, subtract 12. Take 180 minus
the declination to convert the mechanical declination to sky declination.

Configured For Text Box

This text box shows the current hemisphere configuration.

Northern and Southern Buttons

The Northern and Southern buttons are used to configure the mount for operation in either hemisphere.
The default configuration is for the northern hemisphere. When the mount is located in the southern
hemisphere, click the

Southern

button so that the sidereal tracking direction is reversed and the homing

sensor positions can be updated. The control system is automatically “rebooted” so that these changes
take effect.

Reboot/Update Firmware

If control system is emitting continuous beeps (for example the mount has encountered a fixed object like
the side of the pier so that the motors have stopped) the control system should be restarted and then
homed (page 20). To restart the control system, click the

Reboot/Update Firmware

text on the right side

of the

Utilities

tab, then click the

Normal

button under

Reboot Bisque TCS

on the left side of this window.

Figure 82: The Reboot/Update Firmware settings on the Utilities tab.

Normal

Click this button, then click the

Yes

button on the confirmation window to restart the control system for

normal operation.

«
...
148
149
150
151
152
...
»

Содержание ME II




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME II

Бренд: Meade Страницы: 47

Spark Travel 50

Бренд: Discovery Telecom Страницы: 36

OMEGA Muzzleloading 3-9x40

Бренд: Nikon Страницы: 4

Бренд: Officina Stellare Страницы: 40

Бренд: Tasco Страницы: 28

ZENITHSTAR 61 APO

Бренд: William Optics Страницы: 9

Бренд: Stellarvue Страницы: 4

Бренд: Stellarvue Страницы: 6

SVX80T-25SV APO TRIPLET

Бренд: Stellarvue Страницы: 20

PREMIER SVX80T-3SV

Бренд: Stellarvue Страницы: 20

Observer 60 ultra

Бренд: Orion Страницы: 8

Бренд: SKY-WATCHER Страницы: 9

Бренд: Orion Страницы: 8

PhotoScope 85 T* FL Series

Бренд: Zeiss Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды