Panasonic WV-SC384 Скачать руководство пользователя страница 99

Страница: 99 / 142

Configure the HTTPS settings

Click the [Network] tab on the "Network" page. (

☞

Pages 26 and 27: How to display/operate the setup menu)

The settings relating to the HTTPS protocol that can enhance the network security by encrypting the access to
cameras on this page.

The HTTPS settings will be configured in the following procedure.

Note:

• To use the server certificate, you need to apply for the approval and the issue of server certificate by CA.
• Either of the self-signed certificate or the server certificate is available. If both of them are installed, the server

certificate will be used prior to the self-signed certificate.

Generation of the CRT key (SSL encryption key)

Configuration of the connection protocol

Access to the cameras using the HTTPS protocol

Application for the approval by CA

(Certificate Authority) - Issue of the server certificate

Generation of CSR (Certificate Signing Request)

Installation of the server certificate

Generation of the self-signed certificate

When using the server certificate

When using the self-signed certificate

Generation of the CRT key (SSL encryption key) (

☞

page 100)

Generation of the self-signed certificate (

☞

page 101)

Generation of CSR (Certificate Signing Request) (

☞

page 103)

Installation of the server certificate (

☞

page 104)

Configuration of the connection protocol (

☞

page 105)

Содержание WV-SC384















































































































































Результаты поиска

Содержание WV-SC384

Отзывы:

Похожие инструкции для WV-SC384

Бренды по названию

Популярные бренды

Panasonic WV-SC384, Руководство по эксплуатации

Результаты поиска

Содержание WV-SC384

Отзывы:

Похожие инструкции для WV-SC384

Бренды по названию

Популярные бренды