Panasonic WV-SC384 Скачать руководство пользователя страница 66

Страница: 66 / 142

Set mask areas

When "Off" is selected for "Wide dynamic range (WDR)"

SC384

, or "Super Dynamic(SD)"

SW395

SC385

and

"Back light compensation(BLC)", it is possible to compensate for backlight by masking brighter areas.

Step 1

Display the "Image adjust" setup menu. (

☞

Page 58)

Step 2

Click the [Start] button of "Mask area".

→

Borders will appear and the image displayed on the

[Image/Position] tab will be divided into 48 (6x8).

Step 3

Click the divided areas to be masked.

→

The clicked areas will be masked and will become

white. To cancel masking, click the area again.

Step 4

Click the [End] button after completing masking areas.

→

The borders on the image displayed on the [Image/

Position] tab will disappear.

SW395

SC385

SC384

Содержание WV-SC384















































































































































Результаты поиска

Содержание WV-SC384

Отзывы:

Похожие инструкции для WV-SC384

Бренды по названию

Популярные бренды

Panasonic WV-SC384, Руководство по эксплуатации

Результаты поиска

Содержание WV-SC384

Отзывы:

Похожие инструкции для WV-SC384

Бренды по названию

Популярные бренды