Panasonic LS-400 Series Скачать руководство пользователя страница 26

Страница: 26 / 57

5-2. Response Time Change Function

Response time can be switched among four levels:

H-SP (ultra high-speed) / FAST (high-speed) / STD

(standard) / U-LG (ultra long-range).

* The incident light intensity display can display a

maximum value of 4,000 in H-SP (ultra high-speed)

mode and FAST (high-speed) mode. In STD

(standard) mode and U-LG (ultra long-range) mode, it can display up to a maximum value of 9,999.

* In H-SP mode, the interference prevention / copy / single step load / single step save functions cannot be used.

After making settings in H-SP mode and using the copy function or another function in a different mode, turn the

power off and then back on again.

Setting

(high-speed)

(ultra high-speed)

(standard)

(ultra long-range)

150

s (0.15 ms) or less

s (0.08 ms) or less

500

s (0.5 ms) or less

4 ms or less

Response time

H-SP

(ultra high-speed)

FAST

(high-speed)

STD

(standard)

U-LG

(ultra long-range)

Press the
MODE key 5 times.

Press the
Jog switch.

Turn the Jog switch once
toward the ‘

’ direction.

Select the desired response time
by turning the Jog switch.

The digital display will quickly
blink to confirm the setting.

Press the
MODE key once.

Turn the [Jog switch] once toward the ‘

’ direction, to select

‘PRO1 mode’.

Press the [Jog switch] to enter the ‘response time change’
state.

If the [Jog switch] is pressed, the current response time (red)
will be displayed.
* The factory setting is ‘STD (standard)’.

If the [Jog switch] is turned, response time (red) will blink on
the digital display.
Select the desired response time.

If the [MODE key] is pressed once, the amplifier will return to
‘PRO1 mode’.

Press the [MODE key] once, the amplifier will return to ‘RUN
mode’ (normal sensing operation).

Press the [MODE key] 5 times to select ‘PRO mode’.

If the [Jog switch] is pressed, response time (red) will quickly
blink on the digital display and the selected ‘response time’
will be confirmed.

The digital display will not blink (red) if the setting has not
been changed.

* The receiving light sensitivity will be set to the maximum

setting for the mode being set.

Ramco National
(800) 280-6933
www.panasonicsensors.com

Содержание LS-400 Series


























































Результаты поиска

Содержание LS-400 Series

Отзывы:

Похожие инструкции для LS-400 Series

Бренды по названию

Популярные бренды

Panasonic LS-400 Series, Руководство по эксплуатации

Результаты поиска

Содержание LS-400 Series

Отзывы:

Похожие инструкции для LS-400 Series

Бренды по названию

Популярные бренды