Panasonic KX-TDA0480 Скачать руководство пользователя | Manualshive

Страница: 138 / 174

background image

Appendices

138

Installation Manual

A1

Voice Over IP Addressing

The KX-TDA0480 relies on static IP addressing for communications between network
devices. This means that networks in which all addressing is allocated on the basis of dynamic
IP addressing (DHCP/BOOTP) are incompatible with the KX-TDA0480 technology. Hybrid
systems capable of employing both static and dynamic addressing are capable of employing
the KX-TDA0480 technology.
All IP addressing must conform to Internet Protocol addressing standards. The diagram below
illustrates IP addressing for the sample network used in this document.

Sample network configuration

Overall

Subnetting

IP addressing defines subnetting. Each network location has a subnet mask address that helps
to define which digits of an IP address are used for the network address and the host address.
In this case the sample network, the subnet address is the KX-TDA0480 default,
255.255.255.0. The subnet mask addresses for various networks may differ from the default
subnets. In the case of the Internet, the subnet mask address will be provided by the regulating
agency or the IP address provider.

•

The following discussion does not attempt to address the subtleties of IP addressing.

Router

PBX

Router

Router

PSTN

PSTN

PSTN

New York Branch Office

Los Angels Branch Office

San Francisco Branch Office

IP PBX

IP PBX

IP PBX

IP PBX

IP Network

Networking

or

(Default Gateway) 206.184.223.1

(Default Gateway) 200.45.11.1

(SF01) 206.184.223.95

(LA01) 200.45.11.34

(Default Gateway)
133.149.1.1

(NY02) 133.149.1.92

(NY01) 133.149.1.91

Subnet Mask: 255.255.255.0

«
...
136
137
138
139
140
...
»

Содержание KX-TDA0480















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TDA0480

Бренд: B&B Electronics Страницы: 60

Бренд: Evolvere Страницы: 43

ThingPark Partner

Бренд: Actility Страницы: 4

Бренд: Linksys Страницы: 32

Бренд: Sunway Страницы: 102

Бренд: Maxis Страницы: 25

Бренд: Comcast Страницы: 6

Бренд: Comcast Страницы: 13

Бренд: ADT Pulse Страницы: 6

Бренд: ZyXEL Communications Страницы: 477

Micro Commander GC0101

Бренд: Polygon Technologies Страницы: 36

Бренд: Kiwi Страницы: 67

Бренд: 2N Страницы: 102

Бренд: WABCO Страницы: 20

Бренд: RTA Страницы: 80

Бренд: SICK Страницы: 44

Бренд: XAVI Technologies Corp. Страницы: 108

Бренд: Zte Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды