Panasonic KX-TDA0480 Скачать руководство пользователя | Manualshive

Страница: 79 / 174

background image

Logical Installation

Installation Manual

79

4.9

Configure Units

Once a Gateway or Gatekeeper unit has been created using the Unit Information Setup Wizard,
the Maintenance Console Software has created a configuration file (OFDD.VHO) for the unit.
This file must now be configured with data that will allow the unit to operate properly in the
network environment in which it is installed.
The Maintenance Console Software permits all configuration file data to be entered and edited
while off-line. Once the configuration data for one or more units has been entered into the
MCS, each unit's configuration file can be saved to a hard disk and /or uploaded to unit's using
the network interface.

*1

In the procedures discussed in this section, the completed configuration files will be uploaded
to the units using a LAN connection.
See Section 3.4 for additional information about the LAN connection.
To begin the configuration process, highlight the unit to be configured by clicking on the unit's
icon and then select

Edit data

and

Edit configuration

item from the Unit menu.

Note

•

Click the Toolbar Edit Configuration icon.

*1

Additional methods for uploading and downloading configuration files are discussed in Appendix A7 of this document.

«
...
77
78
79
80
81
...
»

Содержание KX-TDA0480















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TDA0480

Бренд: Symantec Страницы: 2

Бренд: OlenCom Страницы: 299

Бренд: Nitgen Страницы: 36

Бренд: Dinstar Страницы: 92

Бренд: CALEFFI Страницы: 20

Бренд: TP-Link Страницы: 63

Бренд: Festo Страницы: 4

Бренд: Festo Страницы: 78

Бренд: Dr. Neuhaus Страницы: 147

Бренд: ViewSonic Страницы: 39

Бренд: OWL Страницы: 16

Бренд: Technicolor Страницы: 98

MediaAccess TG789vn

Бренд: Technicolor Страницы: 128

Бренд: AirLive Страницы: 163

Бренд: EnGenius Страницы: 10

Druid D2 Series

Бренд: Nemtek Страницы: 6

Airspot DSA-3100

Бренд: D-Link Страницы: 79

Бренд: Agilent Technologies Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды