Panasonic KX-TDA0480 Скачать руководство пользователя | Manualshive

Страница: 16 / 174

background image

Planning

16

Installation Manual

•

Under high network load and poor transmission conditions, a fax communication may be
dropped.

•

During a fax connection, the KX-TDA0480 sends a Ring Back Tone (RBT) until a fax
connection is achieved.

2.1.4

DTMF Detection

The KX-TDA0480 provides DTMF detection and regeneration capabilities.

Characteristics

•

Sending units detect and convert DTMF tones for reliable TCP transmission.

•

Receiving units regenerate DTMF tones.

•

Assures accurate and reliable transmission when interfacing with Auto Attendant/Voice
Mail or Interactive Voice Response systems.

•

Selecting the DTMF signal method which the KX-TDA0480 sends from among Auto,
Alphanumeric, and Signal.

Operational limits

•

When a unit is configured to use DTMF regeneration, the feature may introduce some
transmission delay.
In most cases (Voice Mail, IVR, Auto Attendant), it will be the calling party which will need
to send DTMF tones by dialling numbers. As a general rule it is best to avoid duplicating
detection on two communicating KX-TDA0480. This can be accomplished by always
selecting the DTMF detect Outgoing parameter when using DTMF regeneration.
In the example shown in DTMF Detection, two units use DTMF regeneration and are
configured so that the feature is enabled only once irrespective of which unit initiates
communications.

DTMF Detection

IP Network

Voice path used

IP-Gateway Card
(DTMF Outgoing)

IP-Gateway Card
(DTMF Outgoing)

IP-Gateway Card
(DTMF Disabled)

«
...
14
15
16
17
18
...
»

Содержание KX-TDA0480















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TDA0480

Бренд: Extron electronics Страницы: 23

Бренд: Juniper Страницы: 3

Бренд: Sagem Страницы: 27

Ethernet Gateway Version 3

Бренд: Packet Power Страницы: 11

Бренд: ZyXEL Communications Страницы: 56

Бренд: DALCNET Страницы: 22

Бренд: Optimus Страницы: 44

Бренд: 2N Страницы: 134

Бренд: hager Страницы: 130

XTREAM CM4652442-MM

Бренд: Mediacom Страницы: 4

GRP-540M Series

Бренд: ICP DAS USA Страницы: 82

Бренд: ICP DAS USA Страницы: 8

Edge-Core OD200

Бренд: Accton Technology Страницы: 124

Бренд: OleumTech Страницы: 76

Бренд: Eaton Страницы: 131

Бренд: Vega Absolute Страницы: 47

Бренд: ABB Страницы: 11

Smart Wireless Gateway 1410

Бренд: Emerson Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды