Panasonic KX-TDA0480 Скачать руководство пользователя | Manualshive

Страница: 170 / 174

background image

Glossary

170

Installation Manual

RAS Channel

An unreliable channel used to convey the Registration, Admissions, and Status messages
and bandwidth changes between two H.323 entities.

Reliable Transmission

Connection-oriented data transmission that guarantees sequenced, error-free, flow-
controlled transmission of messages to the receiver.

Real-Time Protocol/Real-Time Control Protocol (RTP/RTCP)

IETF specifications for audio and video signal management. Allows applications to
synchronise and spool audio and video information.

Remote maintenance

One of the service functions supported by the KX-TDA0480. The KX-TDA0480 can be
maintained remotely over a network connection. The Maintenance Console Software
supports remote maintenance functions.

Routed Call

Gives call status control of Gatekeeper priority.Path control signal (Q.931) is also sent to
the calling terminal via the Gatekeeper. Although there will be more Gatekeeper load, logs
can be collected accurately for accounting purposes, etc., since the communication status
can be grasped completely.

Signal method

Encoding method of H.245 when transferring DTMF signals on an IP network. The purpose
of this method is to transfer DTMP signals. The transmission time of DTMF signals can be
specified on the receiving side (not available on the KX-TDA0480). For the KX-TDA0480,
the method is selected when the communicating party is H.245 V3 or later.

Static address conversion

Address conversion method that assigns a fixed global address when connecting a device
within the space of a private address to the Internet.

System function

System function is a category of the service functions supported by the KX-TDA0480. This
category separates various functions that compose an internet/intranet telephony network
from a system point of view. This category includes functions such as network building
functions, functions to accommodate various kinds of terminals, and functions needed to
monitor the connection lines.

TCP

Transmission Control Protocol. A reliable networking layer on top of IP.

«
...
168
169
170
171
172
...
»

Содержание KX-TDA0480















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TDA0480

Бренд: ZIEHL-ABEGG Страницы: 23

Бренд: Planet Страницы: 12

Бренд: Bticino Страницы: 28

Бренд: AES Corporation Страницы: 2

Бренд: RTA Страницы: 80

Бренд: Velleman Страницы: 84

RT-RoIP2-Azetti

Бренд: Solidtronic Страницы: 8

Бренд: Solidtronic Страницы: 8

Бренд: Planet Страницы: 8

Бренд: Planet Страницы: 16

Бренд: Planet Страницы: 16

Бренд: Planet Страницы: 131

Бренд: Kasda Страницы: 43

HomePortal 3700HG

Бренд: 2Wire Страницы: 4

NetLinx NXB-CCG-K

Бренд: AMX Страницы: 32

Бренд: Planet Страницы: 30

Бренд: evertz Страницы: 34

Бренд: Ness Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды