Panasonic KX-TDA0480 Скачать руководство пользователя

Страница: 126 / 174

Logical Installation

126

Installation Manual

Use the Gatekeeper information section to configure Gatekeeper parameters.

Reconnect after
errors

Type the number of times that a recovered link is to be detected before the
link will be reestablished as normal.
The times value can also be scrolled up and down with the scrolling
arrows located to the right of the field.

Gatekeeper ID

Type the unit ID number for the Gatekeeper.

Other Gatekeeper
IP address

If a another Gatekeeper is installed in the network, type the IP address of
the other unit.

Use bandwidth
management

Click on the radio button indicating that bandwidth management is to use
(Yes) or not used (No).

Содержание KX-TDA0480















































































































































































Результаты поиска

Содержание KX-TDA0480

Отзывы:

Похожие инструкции для KX-TDA0480

Бренды по названию

Популярные бренды

Panasonic KX-TDA0480, Руководство по установке

Результаты поиска

Содержание KX-TDA0480

Отзывы:

Похожие инструкции для KX-TDA0480

Бренды по названию

Популярные бренды