Panasonic KX-TDA0480 Скачать руководство пользователя | Manualshive

Страница: 27 / 174

background image

Planning

Installation Manual

27

2.2.5

Unit Setup Worksheet

The Unit Setup Worksheet is used to record all of the information needed to install and
configure the KX-TDA0480. Some of this information can be transferred from the network
worksheets discussed earlier in this section.

The worksheet has a front and backside. There is also an extension to the worksheet.

The worksheet is divided into sections that correspond to the Unit Setup Wizard and Edit Data
configuration tabs in the Maintenance Console Software.
Worksheet fields with default values are subtitled with these values in parentheses.

Worksheet examples in this section are for the named units in the Sample Network in Section
2.1

Basic Configuration Overview. Also see the network diagrams in Appendices A1

Voice

Over IP Addressing and A2

Numbering Systems.

Once this worksheet is completed, the information is used to logically configure a unit. The
logical parameters are configured using the Maintenance Console Software. Once this
information is entered into the software, the configuration file is uploaded to the unit and is
recorded in unit’s internal OFDD.VHO file.

The Maintenance Console Software procedures for entering and uploading unit configuration
data are provided in Section 4 Logical Installation of this document.

This worksheet should be completed for each KX-TDA0480 to be installed in the network.
Care must be taken to assure that the information provided is correct and complete. Inaccurate
or incorrect information may result in problems that are difficult to diagnose once the network
is operational.

Reproduction masters for these worksheets are included in Appendix A8

Worksheet Masters

of this document.

«
...
25
26
27
28
29
...
»

Содержание KX-TDA0480















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TDA0480

Бренд: ICP DAS USA Страницы: 96

Бренд: ICP DAS USA Страницы: 38

Бренд: ICP DAS USA Страницы: 17

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 8

UNIGATE IC - Powerlink

Бренд: DEUTSCHMANN AUTOMATION Страницы: 50

10/100Mbps 4-Port Internet Gateway

Бренд: Leviton Страницы: 10

Бренд: FACTBIRD Страницы: 2

Бренд: DISIBEINT Страницы: 4

SMK Access Station Mini

Бренд: Sigfox Страницы: 17

P-660R-T Series

Бренд: ZyXEL Communications Страницы: 9

Бренд: LANSITEC Страницы: 25

Бренд: Telco Страницы: 4

Бренд: BossPac Страницы: 26

Бренд: QUANTUM X Страницы: 56

Бренд: wowvision Страницы: 145

Lightcloud LCGATEWAY/4G

Бренд: RAB Страницы: 16

Бренд: Magnum Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды