background image

356

9 Security

9.13 

Storm 

Control    

9.13

Storm Control 

Use the following window to implement the storm-control settings and 

display its settings.

Choose 

Security > Storm Control

 to display the following window. 

Figure 9-61 Storm Control (Level Type and PPS)

In the section of

 Storm Control Polling Settings

, you can configure the 

following parameters.

Click 

Apply

 to reflect the change.

Parameter 

Overview

Polling Interval

Enter the value regarding a polling interval to use. The 
range is from 5 to 600 (seconds). By default, the value is 
5 (seconds). 

Shutdown Retries

Enter the value regarding the number of shutdown

-

retrials. The range is from 0 to 360. By default, the value 
is 3. If you set the 

Unlimited 

option to on, this function 

becomes disabled. 

Содержание GA-ML Series

















































































































































































































































































































































































































































































































Отзывы: