manualshive.com logo in svg

Panasonic GA-ML Series, Руководство пользователя

Поделиться
Скачать
Panasonic GA-ML Series Скачать руководство пользователя страница 208

206

7 QoS (Quality of Service)

  7.1.6 Queue Rate Limiting    

In the section of

 Limiting Queue Bandwidth

, you can configure the 

following parameters.

 

Click 

Apply

 to check the content changed.

Parameter 

Overview 

From Port/ To Port

Choose the port you use.

Queue ID

Choose a queue ID to be configured. The range of 
values to choose is from 0 to 7. 

Rate Limit (or 
Bandwidth 
Limitation)

Choose and enter the configuration of limiting queue 
band. If you choose 

Minimum Bandwidth

, enter it in 

the entry field where the minimum bandwidth for 
bandwidth-limitation is displayed.

• The range is from 8 to 40,000,000 (Kbps). 

• Enter the number in the entry field where the 

maximum bandwidth for bandwidth limitation is 
displayed. The range is from 8 to 40,000,000 (Kbps). 
If you configure the minimum bandwidth, packets 
transmitted from the queue are guaranteed (or 
assured). If you configure the maximum bandwidth, 
packets transmitted from the queues do not exceed 
the maximum bandwidth. If you configure the 
minimum bandwidth, the aggregation of the 
minimum bandwidth to be configured must be less 
than 75% of the interface bandwidth. Doing so 
ensures the minimum bandwidth (to be configured). 
You do not need to configure the minimally 
guaranteed bandwidth for the strict priority queue. 
The reason is this; if the minimum bandwidth of all 
the queues is satisfied, services are provided with this 
queue traffic first. The configuration of this 
command is attached to the physical port only, but is 
not attached to a port channel. This is the minimally 
guaranteed bandwidth of one CoS, so it cannot be 
used across the whole physical port(s). 

• If  you  choose  the 

Minimum Percent

 option, enter 

the percent-value of the minimum bandwidth in the 
entry field provided. The range is from 1 to 100%. 
Enter the value of the 

Maximum Percent

 in the 

entry field provided. 

• If  you  choose 

None

, the bandwidth limitation is not 

assigned to the port specified.

Содержание GA-ML Series

















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды