Panasonic AJ-PX800G, Руководство по эксплуатации

Страница: 184 / 220

– 184 –
Chapter 10 Network Connection — Network settings
t
When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been
changed, the setting screen termination may take time due to the restart of the network service.
t
All of the IP address, subnet mask, and default gateway must be correctly set.
If a warning [CANNOT ACCESS GATEWAY!] appears at the termination of the setting screen, contact the administrator of the network you use.
t
If you do not use default gateway and DNS, set them to [0.0.0.0].
t
DHCP and DNS may not function properly depending on the network environment.
t
A maximum of 20 connections are saved in the connection history. When this number is exceeded, the oldest entries are deleted.
t
The status of SSID connection destination list is current at the time the list was displayed and is not automatically refreshed.
r
SSID connection destination list screen
1 2 3 4 5
1 Selection status
A checkmark [
l
] is displayed on the currently selected SSID. (This does not show the connection status).
2 SSID
The SSID list registered in the detected SSID and the connection history is displayed. SSIDs are displayed in order from the one with the strongest
signal.
3 Whether there is connection history
[H] is displayed in the SSID that has a past connection history. SSID with past connection histories are displayed even if the camera is outside the
service area.
4 Encryption format
This is the encryption method used by the access point.
5 Radio wave strength
This shows the signal strength of the access point.
4G/LTE setting
[4G/LTE] mode
Use the following procedure when you connect the camera with the 4G/LTE USB modem.
1
Select [4G/LTE] in the main menu → [NETWORK SETUP] → [NETWORK SEL].
2
Select [4G/LTE PROPERTY] and set items as necessary when the main menu → [NETWORK SETUP] → [4G/LTE PROPERTY] is
enabled.
When the setting of [4G/LTE PROPERTY] is required for the connected 4G/LTE USB modem, [4G/LTE PROPERTY] will become enabled.
When following setting is required, enter the information provided from the provider accurately.
[APN]: Sets the APN (access point name) provided from the provider.
[USER ID]: Sets the user name provided from the provider.
[PASSWORD]: Sets the password provided from the provider.
[DIAL NO.]: Sets the phone number. For details, refer to the manual of the provider you have contracted.
3
Check the network connection.
Check whether to connect the camera to the network with 4G/LTE.
[4G/LTE ] is displayed in the screen when network connection is correct. The network status icon on top right of the thumbnail screen will be
displayed in yellow, and the application using the network (FTP) can also be used.
@ @
NOTE
t
The startup time after turning on the power may be longer due to starting of the network.
t
When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been
changed, the setting screen termination may take time due to the restart of the network service.
Wired LAN settings
The settings to connect to computers using the wired LAN are as follows.
1
Set each item in the main menu → [NETWORK SETUP] → [LAN PROPERTY] as necessary.
[DHCP] and [DHCP SERVER] are mutually exclusive.
[MAC ADDRESS]: MAC address of wired LAN (cannot be changed)
[DHCP]: Setting whether to use automatic acquisition via DHCP ( [ENABLE]: Use automatic acquisition/ [DISABLE]: Does not use automatic
acquisition (Factory setting: [ENABLE])
[IP ADDRESS]: IP address (Factory setting: [192.168.0.1])
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])