Panasonic AJ-PX800G, Руководство по эксплуатации

Страница: 164 / 220

– 164 –
Chapter 9 Connecting to External Devices — Connection through the <USB2.0> terminal
3
Set [ON] in the main menu → [NETWORK SETUP] → [USB MODE].
f
The camera is switched to the USB host mode.
f
During USB host mode, [USB STORAGE CONNECTED] is displayed in the center of the viewfinder. If hard disk drive is not connected properly,
[USB STORAGE DISCONNECTED] is displayed.
4
Press the <THUMBNAIL> button.
f
The thumbnail screen is displayed.
f
Ensure that (white) is displayed at the top right of the screen.
f
If a storage device is connected, the icon that indicates storage device status at the top right illuminates. However, a red mark indicates that the
device cannot be used.
5
Exit the USB host mode.
There are two methods:
f
Turn the <POWER> switch of the camera to <OFF>.
f
With the thumbnail screen closed, set [OFF] in the main menu → [NETWORK SETUP] → [USB MODE].
f
Press the USER button to which [USB MODE] has been assigned. Note that this is disabled when a menu or thumbnail is open.
@ @ NOTE
t
The USB 2.0 cable is not supplied with the camera. Prepare a commercially available USB 2.0 cable (double-shielded for noise suppression).
t
In USB host mode, a P2 card can be played back. Camera image and external input cannot be recorded.
Clips written to the hard disk drive cannot be played back on the camera.
t
A storage device cannot be connected to the <USB2.0> terminal (sub-host) (page 20).
t
While connecting a storage device, use the fully charged battery or connect an external DC power supply to the camera to avoid problems in copying
or formatting operations.
t
The <USB2.0> terminal also supports USB bus power (5 V, 0.5 A). However, there are certain devices that cannot run depending on the storage
device used. In such cases, add a separate power supply to the storage device.
t
Some storage devices may not function properly depending on the storage device and cable used.
t
Do not connect multiple storage devices using a hub even if the storage devices are turned off. Do not connect other devices together with your
storage device using a hub.
t
During a format or copy operation, do not unplug the cable, eject the target P2 card, or turn off the camera or the storage device. Rebooting the
camera and the storage device is required.
t
A storage device with the SATA (Serial ATA) or PATA (Parallel ATA) interface connected using a USB conversion cable may not be recognized.
t
Do not connect or disconnect the cable during playback on the camera. Playback may not be performed properly.
Storage device types and available functions
The available functions differ depending on the storage device you will use. The storage device type is displayed after [PARTITION] on the left side of
the storage device explorer screen.
For details, refer to “Storage device information display (explorer screen)” (page 167).
r
Storage device type
Storage device type Features
[TYPE S] A special format to read/write data with high speed by card.
[P2STORE] Indicates P2 STORE (AJ-PCS060G). Writing is disabled.
[FAT]
Storage devices where the primary partition is FAT16 or FAT32. The partition root or CONTENTS folder
under any folders* is the target.
[OTHER]
Indicates other storage devices other than the above. File systems other than FAT16 and FAT32, such as
NTFS.
* The hierarchy of folders is down to the third level and the maximum number of folders is 100. Folders are displayed from the upper hierarchy. Long file names
and file names with double-byte characters are not supported. Examples of folder displays are shown below.
/CONTENTS
Can be displayed.
/SAMPLE/CONTENTS Can be displayed.
/SAMPLE/20140101/CONTENTS
Can be displayed.
/SAMPLE/20140101/1200/CONTENTS Cannot be displayed. (Cannot be displayed since this is a fourth level folder)
r
Storage device types and available functions
Available functions
Storage device type
[TYPE S] [P2STORE] [FAT] [OTHER]
Thumbnail display
l l l
—
Card unit
Card*
1
→ Storage
l
—
l
—
Card*
2
→ Storage — — — —
Storage → Card*
1 l l
— —
Storage → Card*
2
— — — —
Clip unit
Card → Storage
l
*
4
—
l
—
Storage
→
Card
l l l
—
Playback check*
3
— — — —
Clip image display
l l l
—
Format
l
—
l l
*
5